Abstract:Tungsten carbide (WC), celebrated for its exceptional strength, hardness, and chemical inertness, serves as an exemplary reinforcement for copper (Cu) matrix composite (CMC) coatings, significantly enhancing their wear and corrosion resistance. However, the inherent poor wettability and interfacial bonding between WC and Cu during the cold spray additive manufacturing process pose challenges to further performance improvement of these coatings. This study investigates cold-sprayed CMC coatings reinforced with WC particles, both with and without an electroless plated cobalt (Co) shell (Co@WC; at 10 wt.% and 20 wt.%), focusing on their microstructure, mechanical properties, tribological behavior, and electrochemical corrosion resistance. The findings indicate a reduction in CMC coatings` porosity and mean free path (MFP) of reinforcement particles with increasing reinforcement content. Despite slight Co shell damage during deposition, ceramic retention is notably enhanced, reaching up to 149.3%. The microhardness and wear resistance of CMC coating are improved with decreased MFP and increased ceramic content. Compared to the Cu coating, the microhardness of CMC coatings escalates by up to 32.9% (151.8HV0.1), and the specific wear rate is dramatically reduced by up to 84.2%. The Co shell effectively prevents the detachment of Co@WC particles, thereby enhancing the bending and wear resistance. Electrochemical corrosion tests, encompassing open circuit potential (EOCP), polarization curve, and electrochemical impedance spectroscopy (EIS), indicate that lower porosity, high ceramic content and the Co shell substantially boost the corrosion resistance of the CMC coating. Specifically, the coating with 20 wt.% Co@WC (Cu20(Co@WC)) demonstrates superior corrosion resistance compared to the Cu coating, hinting at the potential for further enhancement with increased ceramic content.

Experimental Investigation on Ultrasonic Shot Peening of WC-Co Alloy

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Effect of ultrasonic surface shot peening on the microstructure and properties of Cu-8Cr alloy

Effect of Shot Peening on the Residual Stresses and Microstructure of Tungsten Cemented Carbide

Changes in Surface Integrity of Cemented Tungsten Carbide with Shot Peening Treatment

Effects of Ultrasonic Shot Peening and Multi-arc Ion Plating on Microstructure and Properties of TiAlN-Coated Cemented Carbide Materials

Effect of surface contamination on electrochemical corrosion behavior of ultrasonic shot peened TA2 alloy

Effect of Surface Strengthening by Ultrasonic Shot Peening on TC17 Alloy

Effects Of Wc Crystal Characteristics On Microstructure And Mechanical Property Of Hvof-Sprayed Wc-Cocr Coatings

Cold-sprayed Cu Matrix Composite Coatings with Core-Shell Structured Co@WC Reinforcements on Q235 Steel

Effect of ultrasonic shot peening duration on the microstructure and mechanical properties of CrMnFeCoNi high-entropy alloy

Microstructure Evolution, Hardness, and Tribological Behaviors of Ti-50.8Ni SMA Alloy with Ultrasonic Surface Shot Peening Treatment

Effect of Ultrasonic Shot Peening on the Microstructure, Surface Residual Stress, and Wear Properties of Ti-6al-4v Alloy

Surface Nanocrystallization of Pure Cu Induced by Ultrasonic Shot Peening

Effect of WC-17Co Content on Microstructure, Mechanical Properties and Wear Resistance of WC-17Co/Ni Composites Produced with Cold Spraying

Cooperative enhancement of strength and corrosion resistance through architecture of nanotwins and low angle grain boundary in Ni20Cr alloy

Effect of Dual Shot Peening on Microstructure and Wear Performance of CNT/Al-Cu-Mg Composites

Investigation on microstructure and wear resistance of WC coated aluminum alloy using machine hammer peening

Surface characteristics and microstructure evolution of a nickel-base single crystal superalloy treated by ultrasonic shot peening

Investigation of Wet Shot Peening on Microstructural Evolution and Tensile-Tensile Fatigue Properties of Ti-6Al-4V Alloy

Effect of Ultrasonic Shot Peening on Microstructure and Properties of Variable Polarity Plasma Arc Welding Joints of 7A52 Aluminium Alloy