Abstract:Shot peening (SP) can modify the surface properties of titanium alloys and titanium matrix composites (TMCs). Based on our previous work in the last ten years, the microstructure and mechanical properties of SP treated Ti-6Al-4V (TC4) and (TiB+TiC)/TC4 are summarized in this review. The compressive residual stress (CRS) was formed on the surface after SP. At different SP intensities, the thickness of the surface CRS layer was improved with increasing SP intensities. During the stress peening, the CRS increased evidently, and the increment was proportional to the prestress. Besides, CRS's thermal relaxation was investigated, which showed that the CRS in the whole deformation layer was relaxed. The relaxation mechanism could be explained by the Zener-Wert-Avrami model. The microstrain, the domain size, and the dislocation density of the peened layer were investigated using the Voigt method. The domain size of TC4 was smaller than the composite, and the microstrain of the TC4 was higher than the composite. The average dislocation density was increased after SP due to the existence of reinforcements. Utilizing the Rietveld method to analyze the microstructure after SP, the variations were similar to the Voigt method's results. Also, the composite's stability was higher than TC4 because of the existence of reinforcements. Hardness analysis revealed that the existence of reinforcements raised the hardness. In the peened layer, the surface's hardness was maximum, and it decreased with the increase in depth. At the same temperature, the hardness of the TC4 was smaller than the composite counterpart. Finally, the strengthening mechanism of SP was discussed and summarized based on the above analysis.

Investigation of Wet Shot Peening on Microstructural Evolution and Tensile-Tensile Fatigue Properties of Ti-6Al-4V Alloy

Evaluation of Mechanical Behavior and Surface Morphology of Shot-Peened Ti-6Al-4V Alloy

Effect of surface high density twin microstructure induced by shot peening on the fatigue behavior of Ti-6Al-4V

Characterization on Surface Mechanical Properties of Ti–6Al–4V after Shot Peening

Effect of Ultrasonic Shot Peening on the Microstructure, Surface Residual Stress, and Wear Properties of Ti-6al-4v Alloy

Effects of shot peening on microstructure evolution and mechanical properties of surface nanocrystal layer on titanium matrix composite

Residual Stress Distribution And Microstructure Characterization Of Particle Reinforced Titanium Matrix Composite After Shot Peening Treatment: A Review

The Influence of Shot Peening on the Surface Properties of (Tib+tic)/ti–6al–4v

Research on surface integrity of Ti-6Al-4V alloy with compound treatment of laser shock peening and shot peening

Characterization on Surface Properties of Ti–6Al–4V after Multiple Shot Peening Treatments

Effect of the Conventional Shot Peening and Multiple Shot Peening on Microstructure and Residual Stress of TC17 Titanium Alloy

Investigation on the Residual Stress and Microstructure of (tib+tic)/ti–6al–4v Composite after Shot Peening

The Variations of Microstructures and Hardness of Titanium Matrix Composite (tib + TiC)/Ti–6Al–4V after Shot Peening

The residual stress varying of shot peened TC4-DT titanium alloy

Enhancement of Fatigue Properties of Selective Laser Melting Fabricated TC4 Alloy by Multiple Shot Peening Treatments

Investigation on Experiments and Numerical Modelling of the Residual Stress Distribution in Deformed Surface Layer of Ti–6Al–4V after Shot Peening

In-situ warm shot peening on Ti-6Al-4V alloy: Effects of temperature on fatigue life, residual stress, microstructure and mechanical properties

Microstructure and Mechanical Property of Ti and Ti6Al4V Prepared by an In-Situ Shot Peening Assisted Cold Spraying

Effect of Shot Peening Strengthening on Microstructure and Properties of TC4-DT Titanium Alloy

Surface mechanical property and residual stress stability of nanostructured CNT/Al-Cu-Mg composites induced by shot peening

Molecular modeling of Ti-6Al-4V alloy shot peening: the effects of diameter and velocity of shot particles and force field on mechanical properties and residual stress