Abstract:Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, Ahead of Print. After pneumatic shot peening, compressive residual stress is induced on the surface of the target, which will improve the fatigue life. During the process, surface roughness is also induced, which may reduce the fatigue life. To achieve the optimum compressive residual stress with the smallest surface roughness, the formation mechanism of the residual stress field and the surface topography are revealed. Then, pneumatic shot peening is simulated by using a discrete element method–finite element method coupled model. Based on the effects of four variables (the incident angle θ, the initial shot velocity v0, the shot radius R) and the mass flow rate rm on five parameters (the equivalent plastic strain, the equivalent stress, the surface compressive residual stress, the maximum compressive residual stress), the surface roughness is investigated. The results show that it induces a residual elastic–plastic strain after the impact of a single shot, which can form a crater and a hemispherical residual stress field. After the impact of many random shots, scattered craters connect with each other, therewith a rough and continuous surface topography is formed. Scattered residual stress fields couple with each other, and a constant residual stress layer with the compressive residual stress in the surface and the tensile residual stress in the subsurface are formed. All five parameters are determined by the residual elastic–plastic strain, which increases as the augment of the normal impact velocity, the shot mass, and the coverage rate. Along with the increase of θ and rm, these five parameters firstly increase and then decrease; with the increase of v0 and R, these five parameters increase. Therefore, reasonable values of θ, v0, R, and rm should be chosen to obtain the optimum compressive residual stress with as small surface roughness as possible.

Investigation of residual stress, stress relaxation and work hardening effects induced by shot peening on the fatigue life of AA 6005-T6 aluminum alloy

Enhancing plain fatigue strength in aluminum alloys through shot peening: Experimental investigations and a strain energy density interpretation

Experimental Study on the Effect of Shot Peening and Re-Shot Peening on the Residual Stress Distribution and Fatigue Life of 20CrMnTi

Effects of Conventional and Severe Shot Peening on Residual Stress and Fatigue Strength of Steel AISI 1060 and Residual Stress Relaxation Due to Fatigue Loading: Experimental and Numerical Simulation

Surface characteristics and stress corrosion behavior of AA 7075-T6 aluminum alloys after different shot peening processes

Cumulative Fatigue damage of AA7075-T6 under Shot Peening and Ultrasonic Surface Treatments

Effects of shot peening and artificial surface defects on fatigue properties of 50CrV4 steel

Application of shot peening to improve fatigue properties via enhancement of precipitation response in high-strength Al-Cu-Li alloys

The influence of compressive residual stress on metallurgical and mechanical properties of materials exposed to shot peening: a review

Effect of surface high density twin microstructure induced by shot peening on the fatigue behavior of Ti-6Al-4V

The role of peening processes as a pre‐treatment to anodizing on fatigue behavior of aircraft aluminum alloy

Effect of Micro-Shot Peening on the Fatigue Performance of AISI 304 Stainless Steel

Effect of shot peening parameters on fretting fatigue lifetime

Investigation of Wet Shot Peening on Microstructural Evolution and Tensile-Tensile Fatigue Properties of Ti-6Al-4V Alloy

Simulation and Experimental Investigation of Multi-Step Shot Peening for Surface Crack Repair in Aluminum Alloys

Investigation of Flexural Strength and Surface Hardness in Aluminum 2024-T3 Subjected to Shot Peening Process by Ni Shots

Study of the shot peening surface roughness in fretting

Effect of laser shot peening on precipitation hardened aluminum alloy 6061-T6 using low energy laser

Anti-fatigue strengthening mechanism of conventional shot peening and micro-shot peening on bare and micro-arc oxidation coated 6082-T6 aluminum alloy

Fatigue Properties of Aluminum Alloy Sheet Treated with Shot-Peen Forming in Salt-Spray Environment

Studies on residual stress and surface topography after pneumatic shot peening using discrete element method–finite element method coupled model