Abstract:The microstructure and its relationship with the mechanical properties of an Inconel 718 superalloy fabricated by selective laser melting (SLM) technology were investigated under different post processes, including HT1, HT2, HT2+HIP and as-built conditions. Specifically, HT1 involved solution treatment at 960 degrees C for 1 h followed by air cooling (AC) and aging treatment at 720 degrees C for 8 h with furnace cooling (FC) to 620 degrees C for 8 h. HT2 involved solution treatment at 980 degrees C for 1 h followed by AC and aging treatment at 760 degrees C for 1 h with FC to 650 degrees C for 1 h. HT2+HIP included the same solution and aging treatments as HT2, with an additional Hot Isostatic Pressing (HIP) at 1170 degrees C for 4 hat 100 MPa. The characteristics of the microstructures after different post process and the failure behaviours such as the fractography and the path of microcracks were examined by SEM, TEM and EBSD. The evolution of the manufacturing defects such as loss of diffusion and keyholes are tracked by XCT. After HT1 and HT2 treatments, plenty of rod-like and needle-like delta phase were captured within the grain and on the grain boundaries. There has been a notable enhancement in the yield and ultimate strength of the superalloy. The uneven microstructures formed by the interlacing of fine and coarse grains under HT1 and HT2 conditions, cause strain concentration at the microscopic level, leading to the initiation of microcracks. In addition, the phenomena of growth and merging of defects were captured during the deformation. After adding a HIP process to HT2, the grains become uniform and coarse accompanied by twins in grains and large delta phase on the grain boundaries. Meanwhile, the size and quantity of defects significantly decrease. The ductility at this condition was improved to 12%, but the yield strength decreased to 886 MPa. The coarse grains and the precipitation of large delta phase on the grain boundaries reduce the strength of the superalloy, leading to microcracks easily initiating and propagating along the grain boundaries, resulting in the final failure. This research identifies post-processing effects on the microstructure and properties of SLM-fabricated Inconel 718, offering valuable guidance for optimizing treatment processes.

Effects of ultrasonic shot peening process on the microstructure and mechanical properties of nickel-based superalloys formed by selective laser melting

Effect of ultrasonic shot peening on microstructure and mechanical properties of GH3230 superalloy during selective laser melt solution heat treatment

Mechanical Properties and Fracture Behavior of Laser Powder-Bed-Fused GH3536 Superalloy

Effect of ultrasonic shot peening on microstructure evolution and corrosion resistance of selective laser melted Ti–6Al–4V alloy

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Microstructure Change and Corrosion Resistance of Selective Laser Melted Ti-6Al-4V Alloy Subjected to Pneumatic Shot Peening and Ultrasonic Shot Peening

Analysis of Influence of Ultrasonic Shot Peening on Surface Plastic Behavior of Superalloy

Effect of ultrasonic shot peening duration on the microstructure and mechanical properties of CrMnFeCoNi high-entropy alloy

Effect of ultrasonic shot peening surface alloying on recrystallisation of a single crystal superalloy

Surface characteristics and microstructure evolution of a nickel-base single crystal superalloy treated by ultrasonic shot peening

Effect of Ultrasonic Shot Peening and Laser Shock Peening on the Microstructure and Microhardness of IN738LC Alloys

Impact on Mechanical Properties and Microstructural Response of Nickel-Based Superalloy GH4169 Subjected to Warm Laser Shock Peening

Comparative study of the effects of conventional shot peening and ultrasonic shot peening on very high cycle fatigue properties of GH4169 superalloy

Nanoscale microstructural factors contributing to the improvement of the micromechanical wear properties of mechanical shot-peened nickel-based superalloys

Correlation Between Microstructures and Mechanical Properties of a Slm Ni-Based Superalloy after Different Post Processes

Effect of Ultrasonic-Assisted Surface Plastic Deformation on the Microstructures and Tensile Properties of Discrete Laser Hardening Treated Cr–Ni–Mo Alloyed Steel

Effect of Ultrasonic Shot Peening on the Microstructure, Surface Residual Stress, and Wear Properties of Ti-6al-4v Alloy

Effects of Heat Treatments on the Microstructure and Tensile Properties of IN738 Superalloy with High Carbon Content Fabricated Via Laser Powder Bed Fusion

Effect of ultrasonic shot peening on surface integrity and fatigue performance of single-crystal superalloy

Effect of ultrasonic shot peening surface alloying on microstructure and tribological behavior of Inconel 718 superalloy

Exploring the Strengthening Mechanisms of Additive Manufactured Metals Treated by Ultrasonic Nanocrystal Surface Modification