Abstract:This study examines the effects of laser shock peening parameters on the structural, mechanical, tribological, and corrosion properties of AA5052 aluminum alloy. The LSP process uses specific parameters, detailed in Table 2, to induce ultra-high plastic strains and strain rates in the material. The research demonstrates significant improvements in both surface hardness (48.29% increase) and tensile strength (24.63% increase) for the optimized LSP conditions. The treatment results in a maximum compressive residual stress of 231.02 MPa near the surface, concentrated within a depth of 100 μm. X-ray diffraction analysis reveals the formation of Mg 2 Al 3 (β) precipitates on the LSP surface, along with peak broadening and shifting indicative of residual stress. These precipitates, along with the high dislocation density caused by severe plastic deformation during LSP, are contributed to the enhanced mechanical properties. Electron backscatter diffraction and transmission electron microscopy observations on the LSP-treated AA5052 confirm the introduction of dislocation shifts, deformation twins, and refinement of grain structure. Additionally, the LSP treatment (1.046 × 10 −3 mm/N-m 3 ) significantly improves wear resistance compared to unpeened alloy (4.482 × 10 −3 mm/N-m 3 ), with a wear rate reduction of over 76.6% during the linear reciprocating tribometer. Finally, electrochemical corrosion tests demonstrate superior corrosion resistance in LSP-treated AA5052 (corrosion rate of 0.0116 mm/yr) compared to the unpeened alloy (0.0551 mm/yr). This study demonstrates that LSP significantly enhances the mechanical performance and corrosion resistance of AA5052 alloy, establishing it as a valuable candidate for shipbuilding applications that require superior durability.

Effect of Ultrasonic Shot Peening and Laser Shock Peening on the Microstructure and Microhardness of IN738LC Alloys

Effects of ultrasonic shot peening process on the microstructure and mechanical properties of nickel-based superalloys formed by selective laser melting

Microstructural evolution and mechanical behaviors of Al-Cu-Li alloy processed by laser shock peening

Impact on Mechanical Properties and Microstructural Response of Nickel-Based Superalloy GH4169 Subjected to Warm Laser Shock Peening

On the Microstructure, Residual Stress and Fatigue Performance of Laser Metal Deposited TC17 Alloy Subjected to Laser Shock Peening

Characteristics of microstructure evolution of surface treated IN718 superalloy by warm laser shock peening during long-term aging at high temperatures

Effect of laser shock peening on the tensile behavior and notch sensitivity of Ni-based single-crystal superalloy

A comparative assessment of the effects of laser shock peening and ultrasonic shot peening on surface integrity and ratcheting fatigue performance of HSLA steel

Laser Shock Peening of Ti6Al4V Alloy with Combined Nanosecond and Femtosecond Laser Pulses

Microstructure evolution and mechanical properties of a lamellar near-α titanium alloy treated by laser shock peening

Influencing laser shock peening treatment of the mechanical, tribological, corrosion, and microstructural characteristics on AA5052 alloy

Effect of ultrasonic shot peening surface alloying on microstructure and tribological behavior of Inconel 718 superalloy

Quantification of room temperature strengthening of laser shock peened Ni-based superalloy using synchrotron microdiffraction

Effect of laser shot peening on precipitation hardened aluminum alloy 6061-T6 using low energy laser

Effect of ultrasonic shot peening on microstructure and properties of 301SS

Strengthening effect of laser peening on fatigue performance and life extension of laser cladded IN718 nickel-based alloy parts

Comparison of surface integrity of GH4169 superalloy after high-energy, low-energy, and femtosecond laser shock peening

Surface characteristics and microstructure evolution of a nickel-base single crystal superalloy treated by ultrasonic shot peening

Microstructure and Fatigue Performance of Hard Al Alloy Repaired by Supersonic Laser Deposition with Laser Shock Peening Treatment

Effects of laser shock peening on fatigue crack growth rate and fracture properties of AA2524 aluminum alloy

Influence of post-heat treatments on the microstructure and mechanical properties of Inconel 738 produced by laser directed energy deposition