Abstract:Purpose This study aims to reveal the influences of three-dimensional (3D) printing parameters such as layer heights (0.1 mm, 0.2 mm and 0.4 mm), infill rates (40, 70 and 100%) and geometrical property as tapered angle (0, 0.25 and 0.50) on vibrational behavior of 3D-printed polyethylene terephthalate glycol (PET-G) tapered beams with fused filament fabrication (FFF) method. Design/methodology/approach In this performance, all test specimens were modeled in AutoCAD 2020 software and then 3D-printed by FFF. The effects of printing parameters on the natural frequencies of 3D-printed PET-G beams with different tapered angles were also analyzed experimentally, and numerically (finite element analysis) via Ansys APDL 16 program. In addition to vibrational properties, tensile strength, elasticity modulus, hardness, and surface roughness of the 3D-printed PET-G parts were examined. Findings It can be stated that average surface roughness values ranged between 1.63 and 6.91 μm. In addition, the highest and lowest hardness values were found as 68.6 and 58.4 Shore D. Tensile strength and elasticity modulus increased with the increase of infill rate and decrease of the layer height. In conclusion, natural frequency of the 3D-printed PET-G beams went up with higher infill rate values though no critical change was observed for layer height and a change in tapered angle fluctuated the natural frequency values significantly. Research limitations/implications The influence of printing parameters on the vibrational properties of 3D-printed PET-G beams with different tapered angles was carried out and the determination of these effects is quite important. On the other hand, with the addition of glass or carbon fiber reinforcements to the PET-G filaments, the material and vibrational properties of the parts can be examined in future works. Practical implications As a result of this study, it was shown that natural frequencies of the 3D-printed tapered beams from PET-G material can be predicted via finite element analysis after obtaining material data with the help of mechanical/physical tests. In addition, the outcome of this study can be used as a reference during the design of parts that are subjected to vibration such as turbine blades, drone arms, propellers, orthopedic implants, scaffolds and gears. Social implications It is believed that determination of the effect of the most used 3D printing parameters (layer height and infill rate) and geometrical property of tapered angle on natural frequencies of the 3D-printed parts will be very useful for researchers and engineers; especially when the importance of resonance is known well. Originality/value When the literature efforts are scanned in depth, it can be seen that there are many studies about mechanical or wear properties of the 3D-printed parts. However, this is the first study which focuses on the influences of the both 3D printing parameters and tapered angles on the vibrational behaviors of the tapered PET-G beams produced with material extrusion based FFF method. In addition, obtained experimental results were also supported with the performed finite element analysis.

An Analysis of the Displacements in 3D-Printed PLA Acoustic Guitars

Influence of 3D Printing Direction in PLA Acoustic Guitars on Vibration Response

Effect of 3D-Printed PLA Structure on Sound Reflection Properties

Analysis of PLA Geometric Properties Processed by FFF Additive Manufacturing: Effects of Process Parameters and Plate-Extruder Precision Motion

Experimental and numerical study of orthotropic behavior of 3D printed polylactic acid by material extrusion

Geometrical analysis in material extrusion process with polylactic acid (PLA)+carbon fiber

Electro-Mechanical Characterisation and Damage Monitoring by Acoustic Emission of 3D-Printed CB/PLA

Investigation into the Acoustic Properties of Polylactic Acid Sound-Absorbing Panels Manufactured by 3D Printing Technology: The Influence of Nozzle Diameters and Internal Configurations

The Influence of Manufacturing Parameters on the Mechanical Behaviour of PLA and ABS Pieces Manufactured by FDM: A Comparative Analysis

Experimental and finite element analyses on the vibration behavior of 3D-printed PET-G tapered beams with fused filament fabrication

Analysis of manufacturing and material parameters in 3D-printed polylactic acid (PLA) parts filled with glass powder: mechanical, economic, and environmental assessment

Model-predicted geometry variations to compensate material variability in the design of classical guitars

An Investigation of the Properties of 3D Printing Materials According to Additive Manufacturing Conditions Using Ultrasonic Wave

3D Printing via material extrusion on an acoustic air bed

Characterization of 3D-printed PLA parts with different raster orientations and printing speeds

The effect of processing parameters on the mechanical characteristics of PLA produced by a 3D FFF printer

The Influence of 3D Printing Parameters on the Mechanical Behavior of PLA

Effect of Printing Parameters on the Mechanical Properties of Parts Fabricated with Open-Source 3D Printers in PLA by Fused Deposition Modeling

3D printing PLGA: a quantitative examination of the effects of polymer composition and printing parameters on print resolution

A novel model to estimate the structural properties of PLA-FFF components along any non-orthogonal direction

Characterization of 3D printed plates using ultrasounds