Abstract:It is discovered in this investigation that there exist two different failure modes and a special separation angle which is the demarcation point of the two different failure modes when FDM (Fused Deposition Modelling) 3D printing materials fail under a tensile load. In order to further understand the mechanical properties of FDM 3D printing materials and promote the use of FDM 3D printing materials, their tensile failure strengths at different printing angles and separation angles are measured and analysed theoretically. A new separate-modes of transversely isotropic theoretical failure model is established to predict the tensile failure strength and separation angle of FDM 3D printing PLA (polylactic acid) material based on the hypothesis of transverse isotropy and the classical separate-modes failure criterion. During this research, the tensile specimens designed according to the current test standard ISO (527-2-2012) for plastic-multi-purpose specimens are fabricated in 7 different printing angles (<math>0∘</math>, <math>15∘</math>, <math>30∘</math>, <math>45∘</math>, <math>60∘</math>, <math>75∘</math>, <math>90∘</math>) and three levels of printing layer thickness (0.1 mm, 0.2 mm, 0.3 mm). Experimental results show that the tensile failure strength increases with the increase of the printing angle or the decrease of the layer thickness. Meanwhile, inter-layer failure tends to occur when the printing angle is small and in-layer failure tends to occur when the printing angle is big. In comparison with the results predicted by the established theoretical model, all values of the Generalized-Relative-Root-Mean-Square Error are close to zero and the experimental separation angles are also between <math>45∘</math> and <math>60∘</math>. So the predictive capacity of the theoretical model is affirmed by experimental results.

A novel model to estimate the structural properties of PLA-FFF components along any non-orthogonal direction

Investigating the large strain compression properties of PLA parts manufactured by FDM using experiments and constitutive modeling

Elasto-Plastic Mechanical Modeling of Fused Deposition 3D Printing Materials

An artificial neural network-based predictive model for tensile behavior estimation under uncertainty for fused deposition modeling

The effect of processing parameters on the mechanical characteristics of PLA produced by a 3D FFF printer

Comprehensive characterization of mechanical and physical properties of PLA structures printed by FFF-3D-printing process in different directions

Experimental and numerical study of orthotropic behavior of 3D printed polylactic acid by material extrusion

Development of a Constitutive Model to Predict the Elasto-Plastic Behaviour of 3D-Printed Thermoplastics: A Meshless Formulation

Analysis of PLA Geometric Properties Processed by FFF Additive Manufacturing: Effects of Process Parameters and Plate-Extruder Precision Motion

Experimental analysis and optimization of mechanical properties of FDM-processed polylactic acid using Taguchi design of experiment

Process-Structure Coupled Simulation of Additive Manufactured Components

Investigation on the improvement of mechanical properties and surface quality of the polylactic acid (PLA) fused filament fabrication parts manufactured without and with vibrations dependent utilization

Stiffness prediction of 3D printed fiber-reinforced thermoplastic composites

Effect of infill pattern and build orientation on mechanical properties of FDM printed parts: An experimental modal analysis approach

Machine Learning Study of the Effect of Process Parameters on Tensile Strength of FFF PLA and PLA-CF

The Influence of Manufacturing Parameters on the Mechanical Behaviour of PLA and ABS Pieces Manufactured by FDM: A Comparative Analysis

Mechanical characterization of polylactic acid, polycaprolactone and Lay-Fomm 40 parts manufactured by fused deposition modeling, as a function of the printing parameters

Investigation of mechanical properties in FFF- produced PLA samples using the Erichsen test: application of definitive screening and RSM

Manufacturing-induced stochastic constitutive behaviors of additive manufactured specimens: testing, data-driven modeling, and optimization

Influence of Build Orientation and Part Thickness on Tensile Properties of Polyamide 12 Parts Manufactured by Selective Laser Sintering

Tensile failure strength and separation angle of FDM 3D printing PLA material: Experimental and theoretical analyses