Abstract:The material extrusion 3D printing process known as fused deposition modeling (FDM) has recently gained relevance in the additive manufacturing industry for large-scale part production. However, improving the real-time monitoring of the process in terms of its mechanical properties remains important to extend the lifespan of numerous critical applications. To enhance the monitoring of mechanical properties during printing, it is necessary to understand the relationship between temperature profiles and ultimate tensile strength (UTS). This study uses a cyber–physical production system (CPPS) to analyze the impact of four key thermal parameters on the tensile properties of polylactic acid (PLA). Layer thickness, printing speed, and extrusion temperature are the most influential factors, while bed temperature has less impact. The Taguchi L-9 array and the full factorial design of experiments were implemented along with the deposited line's local fused temperature profile analysis. Furthermore, correlations between temperature profiles with the bonding strength during layer adhesion and part solidification can be stated. The results showed that layer thickness is the most important factor, followed by printing speed and extrusion temperature, with very close influence between each other. The lowest impact is attributed to bed temperature. In the experiments, the UTS values varied from 46.38 MPa to 56.19 MPa. This represents an increase in the UTS of around 17% from the same material and printing design conditions but different temperature profiles. Additionally, it was possible to observe that the influence of the parameter variations was not linear in terms of the UTS value or temperature profiles. For example, the increase in the UTS at the 0.6 mm layer thickness was around four times greater than the increase at 0.4 mm. Finally, even when it was found that an increase in the layer temperature led to an increase in the value of the UTS, for some of the parameters, it could be observed that it was not the main factor that caused the UTS to increase. From the monitoring conditions analyzed, it was concluded that the material requires an optimal thermal transition between deposition, adhesion, and layer solidification in order to result in part components with good mechanical properties. A tracking or monitoring system, such as the one designed, can serve as a potential tool for reducing the anisotropy in part production in 3D printing systems.

Experimental and numerical study of orthotropic behavior of 3D printed polylactic acid by material extrusion

Mechanical properties of 3D printed polylactic acid elements: Experimental and numerical insights

Orthotropic elastic behaviors and yield strength of fused deposition modeling materials: Theory and experiments

Design of Experiments to Compare the Mechanical Properties of Polylactic Acid Using Material Extrusion Three-Dimensional-Printing Thermal Parameters Based on a Cyber–Physical Production System

Experimental analysis and optimization of mechanical properties of FDM-processed polylactic acid using Taguchi design of experiment

Mechanical characterization of polylactic acid, polycaprolactone and Lay-Fomm 40 parts manufactured by fused deposition modeling, as a function of the printing parameters

Characterization of 3D-printed PLA parts with different raster orientations and printing speeds

The effect of processing parameters on the mechanical characteristics of PLA produced by a 3D FFF printer

Mechanical Properties of 3D-Printing Polylactic Acid Parts subjected to Bending Stress and Fatigue Testing

On strain rate and temperature dependent mechanical properties and constitutive models for additively manufactured polylactic acid (PLA) materials

Elasto-Plastic Mechanical Modeling of Fused Deposition 3D Printing Materials

Comprehensive characterization of mechanical and physical properties of PLA structures printed by FFF-3D-printing process in different directions

Prediction of The Mechanical Behavior of Polylactic Acid Parts with Shape Memory Effect Fabricated by FDM

Impact of strain rate on mechanical properties of polylatic acid fabricated by fusion deposition modeling

Experimental Study of the Tensile Behavior of Structures Obtained by FDM 3D Printing Process

The Torsional Characterization of 3D‐Printed Polylactic Acid Parts With Alternating Additive Manufacturing Parameters

Experimental and numerical investigations on the thermoforming of 3D-printed polylactic acid parts

Micromechanical modeling and numerical homogenization calculation of effective stiffness of 3D printing PLA/CF composites

A method to predict the ultimate tensile strength of 3D printing polylactic acid (PLA) materials with different printing orientations

Geometrical analysis in material extrusion process with polylactic acid (PLA)+carbon fiber

The Influence of 3D Printing Parameters on the Mechanical Behavior of PLA