Abstract:The material extrusion 3D printing process known as fused deposition modeling (FDM) has recently gained relevance in the additive manufacturing industry for large-scale part production. However, improving the real-time monitoring of the process in terms of its mechanical properties remains important to extend the lifespan of numerous critical applications. To enhance the monitoring of mechanical properties during printing, it is necessary to understand the relationship between temperature profiles and ultimate tensile strength (UTS). This study uses a cyber–physical production system (CPPS) to analyze the impact of four key thermal parameters on the tensile properties of polylactic acid (PLA). Layer thickness, printing speed, and extrusion temperature are the most influential factors, while bed temperature has less impact. The Taguchi L-9 array and the full factorial design of experiments were implemented along with the deposited line's local fused temperature profile analysis. Furthermore, correlations between temperature profiles with the bonding strength during layer adhesion and part solidification can be stated. The results showed that layer thickness is the most important factor, followed by printing speed and extrusion temperature, with very close influence between each other. The lowest impact is attributed to bed temperature. In the experiments, the UTS values varied from 46.38 MPa to 56.19 MPa. This represents an increase in the UTS of around 17% from the same material and printing design conditions but different temperature profiles. Additionally, it was possible to observe that the influence of the parameter variations was not linear in terms of the UTS value or temperature profiles. For example, the increase in the UTS at the 0.6 mm layer thickness was around four times greater than the increase at 0.4 mm. Finally, even when it was found that an increase in the layer temperature led to an increase in the value of the UTS, for some of the parameters, it could be observed that it was not the main factor that caused the UTS to increase. From the monitoring conditions analyzed, it was concluded that the material requires an optimal thermal transition between deposition, adhesion, and layer solidification in order to result in part components with good mechanical properties. A tracking or monitoring system, such as the one designed, can serve as a potential tool for reducing the anisotropy in part production in 3D printing systems.

3D Printing via material extrusion on an acoustic air bed

Recent progress in acoustic field-assisted 3D-printing of functional composite materials

Elasto-dynamic characterization of material extrusion infills using homogenization methods

Dynamic Interface Printing

SonoPrint: Acoustically Assisted Volumetric 3D Printing for Composites (Adv. Mater. 40/2024)

Direct 3D printing functional surfaces stacked with microstructured filaments

Design and Construction of a Low-Cost-High-Accessibility 3D Printing Machine for Producing Plastic Components

Relating Polymer Reptation to Material Extrusion 3D Printing: Mechanical Testing and Mathematical Modeling

A low-cost, open-source 3D printer for multimaterial and high-throughput direct ink writing of soft and living materials

Electrospray printing: Unravelling the history of a support free three-dimensional additive manufacturing technology

In Situ Foam 3D Printing of Microcellular Structures Using Material Extrusion Additive Manufacturing.

Acoustic-assisted 3D Printing Based on Acoustofluidic Microparticles Patterning for Conductive Polymer Composites Fabrication

Mechanical characterization of additively manufactured polymers using ultrasonic nondestructive testing

Newtonian liquid-assisted material extrusion 3D printing: Progress, challenges and future perspectives

Material extrusion of thermoplastic acrylic for intraoral devices: Technical feasibility and evaluation

Experimental and numerical study of orthotropic behavior of 3D printed polylactic acid by material extrusion

An Investigation of the Properties of 3D Printing Materials According to Additive Manufacturing Conditions Using Ultrasonic Wave

Electro-Mechanical Characterisation and Damage Monitoring by Acoustic Emission of 3D-Printed CB/PLA

Design of Experiments to Compare the Mechanical Properties of Polylactic Acid Using Material Extrusion Three-Dimensional-Printing Thermal Parameters Based on a Cyber–Physical Production System

The development of a conical screw-based extrusion deposition system and its application in fused deposition modeling with thermoplastic polyurethane

3D Printed Functional and Biological Materials on Moving Freeform Surfaces