Abstract:Fused deposition modeling (FDM) is an extrusion-based AM process that is widely used due to its cost-effectiveness and user friendly. However, FDM also has some limitations such as the appearance of seam lines between layers and the production of excess material residue leading to poor surface finish, poor bonding between layers and porosity. This paper presents the findings on the application of ultrasonic vibration in an open-source FDM 3D printer to investigate its effect on the mechanical properties and microstructure of acrylonitrile butadiene styrene (ABS) and Polylactic Acid (PLA) samples. Two units of ultrasonic piezoelectric transducer were clamped horizontally on the surface of the 3D printer platform. The ultrasonic vibration was transmitted directly to the platform while the sample received vibration with a specific frequency while the printing process commences. Two process parameters, namely build orientation and ultrasonic vibration were selected to analyze their significance and optimization on the mechanical properties and the microstructure of the printed samples. High compressive and low surface roughness are required to have the best properties for the printed sample. Therefore, the optimization parameters are performed with these settings where the compressive strength is maximized and the surface roughness is minimized. The result shows that the overall compressive strength in ABS and PLA samples created in the Z-axis orientation is higher than in the X-axis orientation. However, the compressive strength of ABS and PLA samples is not much different after the ultrasonic vibration was applied during the printing process. The microstructure analysis shows that bonding between the layers is similar when applying ultrasonic vibration for both ABS and PLA samples. Furthermore, the result indicates that the surface roughness increased at 10 kHz and then decreased or became smoother at 20 kHz for both ABS and PLA material samples. The analysis shows that the build orientation significantly affects the compressive strength in ABS and PLA samples. However, the ultrasonic vibration has no considerable impact. In surface roughness, the build orientation and ultrasonic vibration significantly affect ABS samples. However, the PLA samples are only slightly affected. The optimum parameters for both materials are found where Z-axis orientation and 0 kHz of the ultrasonic vibration samples gave the best compressive strength and surface roughness value.

Mechanical characterization of additively manufactured polymers using ultrasonic nondestructive testing

Ultrasonic Nondestructive Evaluation of Additively Manufactured Photopolymers

Nondestructive ultrasonic evaluation of fused deposition modeling based additively manufactured 3D-printed structures

Evolution of microstructure and thermo‐mechanical attributes of fiber reinforced polyamide during fused deposition modeling 3D printing: A comprehensive characterization study

Ultrasonic nondestructive characterization and its role in the development and implementation of additive manufacturing processes

Elasto-dynamic characterization of material extrusion infills using homogenization methods

Finite element simulation and experimental verification of ultrasonic non-destructive inspection of defects in additively manufactured materials

A non-destructive resonant acoustic testing and defect classification of additively manufactured lattice structures

Investigation of the Effect of Artificial Internal Defects on the Tensile Behavior of Laser Powder Bed Fusion 17–4 Stainless Steel Samples: Simultaneous Tensile Testing and X-Ray Computed Tomography

Effect of ultrasonic vibration on the mechanical properties of 3D printed acrylonitrile butadiene styrene and polylactic acid samples

Characterization of 3D-printed PLA parts with different raster orientations and printing speeds

An Investigation of the Properties of 3D Printing Materials According to Additive Manufacturing Conditions Using Ultrasonic Wave

Evaluation of the influence of ultrasonic vibration on physical, tensile, and morphological properties of fused deposition modeled specimens

Mechanical characterization and experimental modal analysis of 3D Printed ABS, PC and PC-ABS materials

Toward In-situ Characterization of Additively Manufactured Parts Using Nonlinear Resonance Ultrasonic Spectroscopy

Tensile testing data of additive manufactured ASTM D638 standard specimens with embedded internal geometrical features

Investigating the Mechanical Properties of Polymer Samples from Different Additive Manufacturing Processes Using Ultrasonic Phase Spectroscopy

Characterization of 3D printed plates using ultrasounds

Comprehensive characterization of mechanical and physical properties of PLA structures printed by FFF-3D-printing process in different directions

Process-Structure Coupled Simulation of Additive Manufactured Components

Additive manufacturing of mechanical testing samples based on virgin poly (lactic acid) (PLA) and PLA/wood fibre composites