Abstract:Transverse mechanical properties of titanium matrix composites (TMCs) play an important role during its engineering service. Although SiCf / TC17 composite is one of the most promising TMC candidates for aeroengine, as we know its transverse properties have not been reported yet until now. In this work, the transverse strength of single SiC fiber reinforced TC17 composite was evaluated using cruciform specimen. The surface and cross-section of fractured specimen were investigated by SEM to determine the failure position during tensile test. Finite element simulation method was also used to analyze the mechanism of interfacial failure and crack propagation. During the transverse tensile test of single fiber specimen, the initial non-linearity in the stress-strain curve occurred at the stress of (271 +/- 12) MPa, which indicated the beginning of fiber-matrix interface failure. SEM observation showed that the crack in the center of sample appeared at the interface of reaction layer and carbon coating with a 24 degrees similar to 68 degrees angle to the applied loading direction and its length extended with the increase of the applied stress. The finite element simulation results based on bilinear cohesive element model showed that transverse fracture of composite interface was shear failure mode, which agreed well with the test results. Before the occurrence of non-linearity in the stress-strain curve, the crack initiated at the circular interface between reaction layer and carbon coating with a 40 degrees similar to 50 degrees angle to the applied loading direction. Crack initiation locations in test samples were different with those in simulation samples, because the actual composite interface was rough and some micro-flaws formed in the interface, whereas it was assumed to be an ideal rigid interface for simulation. Then the crack propagated along both circumferential and axial directions because of the shear stress. With the crack growing, the interface close to 0 degrees angle to the applied loading direction failed first caused by the radial tensile stress, whereas the interface near 90 degrees failed later as a result of circumferential shear stress. After complete failure of the interface, stress redistribution occurred around the SiC fiber and the interface separation increased with the increasing of the applied load, which gave rise to the yielding and deforming of the matrix near fiber until the final fracture of the composite.

Abnormal mechanical hysteresis behavior of Tyranno-ZMI SiC/SiC containing Ti3Si(Al)C2

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Influence of Reinforcement with Multimodal Distribution on Thermophysical Properties and Fracture Behavior in Al-Si/SiC Composites Infiltrated under Super-Gravity Field

Effects of single-phase and Co-deposited interphases on mechanical hysteresis behavior in T700 TM mini-C f /SiC composites

Residual stress variation in SiCf/SiC composite during heat treatment and its effects on mechanical behavior

Research on Single SiC Fiber Reinforced TC17 CompositesUnder Transverse Tension

Modeling Loading/Unloading Hysteresis Behavior of Unidirectional C/SiC Ceramic Matrix Composites

Multiscale Failure Mechanism Analysis of SiC Fiber-Reinforced TC17 Composite Subjected to Transverse Tensile Loading at Elevated Temperature

Micromechanical modeling cyclic loading/unloading hysteresis loops of 3D needle-punched C/SiC ceramic-matrix composites

Interface structure and tensile failure behaviour of novel SiC f /Ti–Ti 2 AlNb hybrid laminated composite material

The thermo-mechanical coupling failure mechanisms of C/SiC riveted joint considering deposited SiC matrix and interference fit

Thermal cycling of silicon carbide whisker reinforced ZL101A composite

High-Temperature Fatigue Degradation Behaviors of a 3D Braided C/SiC with a Thin Interlayer in Different Dry Oxygen Atmospheres

Microstructural Characteristics and Mechanical Behavior of SiC(CNT)/Al Multiphase Interfacial Micro-Zones Via Molecular Dynamics Simulations

The oxide-layer configuration alteration and pseudo-ductile crack propagation mechanisms in composites induced by different relative thicknesses of CVI HfC-SiC multiphase matrix

Micromechanical Analysis of SiC/Ti6Al4V Composite Under Complex Stress State

Microstructures and mechanical properties of in-situ SiC-TiB2 ceramic composites fabricated by reactive melt infiltration

Failure Evaluation of a SiC/SiC Ceramic Matrix Composite During In-Situ Loading Using Micro X-ray Computed Tomography

In situ preparation of a SiC–TiB2 composite and its wear fracture mechanism at high temperatures

Mechanical properties and damping capacity of SiC p /TiNi f /Al composite with different volume fraction of SiC particle

Effect of SiC on the anti-ablation resistance and flexural strength of (Hf-Ta-Zr)C-C/C composites