Abstract:Powder metallurgy (PM) α + β Ti-4Al-4Mo-4Sn-0.5Si alloys were fabricated through thermomechanical powder consolidation of TiH 2 -based powder compacts with two different processing routes: one involving blending the elemental powders (BE route) and the other involving mechanical milling a blend of elemental powders (MM route). With the MM + annealing + solution and aging (STA) route, a hierarchical microstructure consisting of necklace-like micron-scaled grain boundary α (α GB ) segments and isolated submicron-scaled primary α (α p ) rods dispersed in a β transformed structure (β t ) matrix containing a high number density of nano-scaled secondary α (α s ) laths was produced in the alloy. The alloy with the hierarchical microstructure achieved an excellent combination of a very high yield strength of 1339 MPa,an ultimate tensile strength of 1467 MPa and an excellent ductility of 10.4%. The increased strength was mainly due to the high fraction of β t matrix in which the fine-dispersed α s precipitates with different orientations efficiently blocked the dislocation motion during deformation. The excellent ductility achieved despite of the high flow stress can be attributed to the elimination of strain concentration in the α GB segments which prevented their cracking prior to the material reaching the necking point during plastic deformation. This was in contrast with the typical α/β t lamellar microstructure of the same alloy composition obtained with the BE + same heat treatment route where strain concentration in the α GB plates occurred due to the direct slip transmission from α colonies to adjacent parent α GB grains during plastic deformation, thus resulting in intergranular premature cracking. TEM observation demonstrated that the strain gradient from the α/β t interfaces to the domain interiors of both α GB segments and α p rods activated a high density of geometrically necessary dislocations near the interfaces, and caused an obvious synergistic strengthening effect which also contributed to the slow drop of strain hardening rate and thus was beneficial to improving the ductility.

Microstructure evolution and mechanical properties of commercial pure titanium subjected to rotary swaging

Mechanical properties and microstructure of heterogeneous commercial pure titanium prepared by rotary swaging and annealing

Microstructure of the Advanced Titanium Alloy VT8M-1 Subjected to Rotary Swaging

Gradient nanostructure, phase transformation, amorphization and enhanced strength-plasticity synergy of pure titanium manufactured by ultrasonic surface rolling

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

Microstructure and mechanical properties evolution of Ti-13Nb-13Zr alloy processed by ECAP-Conform and rotary swaging

Achieving Enhanced Tensile Strength-Ductility Synergy Through Phase Modulation in Additively Manufactured Titanium Alloys

Enhancement of tensile strength and ductility of titanium with a bimodal structure

Ascertaining the microstructural evolution and strengthening mechanisms of the gradient nanostructured pure titanium fabricated by ultrasonic surface rolling process

Evolution of microstructure, macrotexture and mechanical properties of high strength biomedical TA4 pure titanium during multi-pass ECAP

Microstructure and Physico-Mechanical Properties of Biocompatible Titanium Alloy Ti-39Nb-7Zr after Rotary Forging

Influence of Initial Textures on Microstructure and Mechanical Properties of Commercially Pure TA2 Titanium Sheet Pre-Strained by Cryorolling

Effect of Repetitive Bending and Straightening Process on Microstructure Properties and Deformation Mechanism of A Ti–Al–Cr–Mo Alloy

Optimizing strength and ductility synergy achieved by multistage strain hardening in gradient recrystallized pure titanium

Enhanced Surface Mechanical Properties and Microstructure Evolution of Commercial Pure Titanium under Electropulsing-Assisted Ultrasonic Surface Rolling Process

A novel cryogenic rolling method for commercially pure titanium sheets featuring high strength and ductility

α" martensite engineering: A strategy to achieve high yield strength and low yield ratio synergy for dual-phase titanium alloy

Effect of rotary swaging on the microstructure and mechanical properties of high-strength Mg-Mn-Al-Ca-Zn alloys

Effect of Microstructure on High-Speed Tensile Mechanical Properties of Ti-1300 Alloy

Achieving high strength-ductility synergy in a hierarchical structured metastable β-titanium alloy using through-transus forging

Hierarchical microstructure and strain partition of a PM α + β titanium alloy with an ultrahigh strength-ductility synergy