Abstract:The demand for polished silicon wafers has increased significantly in recent years to cater to the development of the semiconductor industry. For example, polished silicon wafer has direct applications in integrated circuits, radio frequency amplifiers, micro-processors, micro-electromechanical systems, etc. To carry out mechanical polishing, lapping, grinding, or single-point diamond turning of silicon, diamond abrasives were extensively used before the implementation of chemo-mechanical polishing. During the diamond-based polishing, a few problems have already been identified, such as the formation of an amorphous phase, heat-affected zones, low material removal, etc. Some research work has also reported that nano-structured abrasives lead to a thin layer of the amorphous phase and a better material removal rate. In the same direction, a molecular dynamics simulation is carried out in this paper to investigate the mechanism of material removal from monocrystalline silicon during the diamond-abrasive-based polishing process. The present work is mainly focused on the dynamics of material removal phenomena near the abrasive particles at the nanometric scale by considering stress, lattice, cohesive energy, etc. This reveals that a higher value of indentation force results in surface buckling, which creates a zone of both compressive and tensile stresses, which increases the coordination number and forms β-silicon just ahead of the abrasive particle. This mechanism happens by developing a β-silicon phase on the surface with a thickness beyond a certain value of indentation force on the zone of compression. Buckling on this phase happens due to stress localisation in compression, as the flow stress of this phase is less than that of diamond cubic lattices. To avoid the mechanism of surface buckling and process silicon material on the surface, the indentation force needs to be maintained below a critical value. In the present case, it was found that the indentation force of less than or equal to 190 nN for the abrasive size of φ8 nm does the material removal by surface processing only without surface buckling. It was also found that surface processing helps to reduce the depth of the amorphous layer significantly without compromising the material removal rate or the generation of a wavy surface. Thus, the present mechanism will help in the polishing of silicon with minimum defects and reduce processing time for the final stage of polishing towards manufacturing ultra-smooth and planer surfaces.

Surface Finish Enhancement of Si(100) with Single Pole Magnetic Abrasive Finishing using Chemical Oxidizers and Alumina Slurry

Surface modulation to enhance chemical mechanical polishing performance of sliced silicon carbide Si-face

Optimization of polishing fluid composition for single crystal silicon carbide by ultrasonic assisted chemical-mechanical polishing

Experimental Analysis of Polishing of Hybrid Aluminium Metal Matrix Composite Reinforced with SiC, ZrO2, and NiTi Particles Using a Developed Rotary Abrasive Float Polishing System

Mechanism of surface modification on monocrystalline silicon during diamond polishing at nanometric scale

Nano-Precision Synergistic Finishing Process Integrated ELID-Grinding and MRF

Research on a new method for optimizing surface roughness of cavitation abrasive flow polishing monocrystalline silicon

Achieving Ultralow Surface Roughness and High Material Removal Rate in Fused Silica Via a Novel Acid SiO2 Slurry and Its Chemical-Mechanical Polishing Mechanism

A combination process of magnetorheological finishing and computer controlled optical surfacing on single-crystal silicon surface

Chemical mechanical polishing of silicon carbide (SiC) based on coupling effect of ultrasonic vibration and catalysis

Improving Surface Electrochemical Polishing Quality of Additive Manufactured AlSi10Mg by Reconstituting the Si Phase

Chemical mechanical polishing of silicon wafers using developed uniformly dispersed colloidal silica in slurry

Polishing single-crystal silicon carbide with porous structure diamond and graphene-TiO2 slurries

Research on the Chemical Mechanical Polishing Process of Aluminum Alloy Wafers with Acidic Slurry

Application of surface analysis in study on removal mechanism and abrasive selection during fused silica chemical mechanical polishing

Single crystal silicon wafer polishing by pretreating pad adsorbing SiO2 grains and abrasive-free slurries

Chemical Mechanical Polishing (CMP) of On-Axis Si-face 6H-Sic Wafer for Obtaining Atomically Flat Defect-Free Surface

Investigation on Electrical Enhanced Photocatalysis Polishing of Single-Crystal Silicon Carbide Substrates

Experimental investigation on the effet of input paramètres on surface roughness and MRR of abrasive flow machining process

Tribochemical mechanisms of abrasives for SiC and sapphire substrates in nanoscale polishing

Experimental Study on Shear Rheological Polishing of Si Surface of 4H-SiC Wafer