Abstract:Commonly used methods for increasing the preferred orientation of n‐type Bi2Te3 include liquid phase hot deformation (LPHD) and traditional hot forging (HF). This work, as an insightful understanding of the HF method, discloses the intrinsic mechanisms of both superior thermoelectric and robust mechanical properties, aiming to shed light on texture engineering utilized for viable micro‐refrigeration applications. Thermoelectric refrigeration is one of the mature techniques used for cooling applications, with the great advantage of miniaturization over traditional compression refrigeration. Due to the anisotropic thermoelectric properties of n‐type bismuth telluride (Bi2Te3) alloys, these two common methods, including the liquid phase hot deformation (LPHD) and traditional hot forging (HF) methods, are of considerable importance for texture engineering to enhance performance. However, their effects on thermoelectric and mechanical properties are still controversial and not clear yet. Moreover, there has been little documentation of mechanical properties related to micro‐refrigeration applications. In this work, the above‐mentioned methods are separately employed to control the macroscopic grain orientation for bulk n‐type Bi2Te3 samples. The HF method enabled the stabilization of both composition and carrier concentration, therefore yielding a higher quality factor to compare with that of LPHD samples, supported by DFT calculations. In addition to superior thermoelectric performance, the HF sample also exhibited robust mechanical properties due to the presence of nano‐scale distortion and dense dislocation, which is the prerequisite for realizing ultra‐precision machining. This work helps to pave the way for the utilization of n‐type Bi2Te3 for commercial micro‐refrigeration applications.

General design of high-performance and textured layered thermoelectric materials via stacking of mechanically exfoliated crystals

A General Strategy for Designing Two-Dimensional High-Efficiency Layered Thermoelectric Materials

Prominent texturing and enhanced thermoelectric performance of misfit layered (PbS)1.18(TiS2)2 via an exfoliation-restacking approach

Microstructures and Thermoelectric Properties of GeSbTe Based Layered Compounds

Layered Oxygen-Containing Thermoelectric Materials: Mechanisms, Strategies, and Beyond

Layered thermoelectric materials: Structure, bonding, and performance mechanisms

Design of N‐Type Textured Bi2Te3 with Robust Mechanical Properties for Thermoelectric Micro‐Refrigeration Application

Remarkable effects of shear-exfoliation and restacking on microstructural texturing and thermoelectric properties of AgCrSe2

High thermoelectric performance realized through manipulating layered phonon-electron decoupling

Deformation Mechanisms in High-Efficiency Thermoelectric Layered Zintl Compounds

Direct Melt-Calendaring of Highly Textured (Bi,Sb)2Te3 Thick Films: Superior Thermoelectric and Mechanical Performance via Strain Engineering

Designing Cost-Performance Porous Thermoelectric Materials by Interface Engineering Through Atomic Layer Deposition

Morphology and Texture Engineering Enhancing Thermoelectric Performance of Solvothermal Synthesized Ultralarge SnS Microcrystal

Plastically Mg3(Sb,Bi)2-based thermoelectric compounds with enhanced texture via cold-deformation

Realizing high thermoelectric performance in p-type CaZn2Sb2-alloyed Mg3Sb2-based materials via band and point defect engineering

Thermal Stability Optimization of Single-Leg Skutterudite-Based Thermoelectric Devices Based on Lattice Distortion Effects

Engineering Natural Layered Framework for Low and Anisotropic Thermal Conductivity

Melt-Centrifuged (bi,sb)2 Te3 : Engineering Microstructure Toward High Thermoelectric Efficiency.

Enhanced thermoelectric performance of orientated and defected SnTe

Hierarchical structures lead to high thermoelectric performance in Cu m+n Pb 100 Sb m Te 100 Se 2m (CLAST)

Enhanced Thermoelectric Performance of N-Type Bi2Te2.7Se0.3 Via a Simple Liquid-Assisted Shear Exfoliation