Abstract:Following the nuclear disaster at Fukushima in Japan in 2011, there is a growing search for novel cladding materials that can displace Zirconium in light water reactors. In this paper, niobium (Nb), titanium (Ti), vanadium (Va) and Inconel-600 alloy are selected as possible innovative cladding materials that have high melting points and resist corrosion. MCNPX code was used to simulate these cladding materials in a standard pressurized water reactor assembly. The impact of these materials on the reactor safety aspects was discussed in terms of the depletion calculations at the unit cell and assembly levels. The included reactor safety aspects in this work are effective multiplication factor (K eff ), cycle length, relative fission power, reactivity coefficients, reactivity worth, fission products and actinides, neutron spectrum, spectral index, radial power distribution and peaking factor. For each proposed cladding material, the study focused on determining the required thickness (at constant enrichment) and evaluating the suitable enrichment (at constant cladding thickness) to obtain the same cycle length of zirconium. The simulation depicted that the lowest decrease of cycle length was observed for niobium which contributed to reducing the Zirconium cycle length by 15%. Meanwhile, the high absorbing cladding materials such as Ti, Va and Inconel-600 reduced the Zirconium cycle length by 29%, 32% and 40%, respectively. Enhanced negativity of fuel temperature coefficient (FTC), moderator temperature coefficient (MTC) and void reactivity coefficient are noticed for Ti, Va, and Inconel-600 at the BOL. On the other hand, Zr and Nb provide the most negativity of reactivity coefficients at the MOL and EOL owing to the low inventory of Pu-239 and fission products. The control rod worth values of Zr and Nb are larger than those of Ti, Va and Inconel-600 throughout the fuel depletion thanks to the softening of neutron spectrum in the case of Zr and Nb. In terms of minimizing the radioactive waste, Nb offers the second lowest inventory of fission products and actinides after zirconium. Finally, the peaking factors for Inconel-600, Va and Ti are slightly higher than those for Zr and Nb. As a consequence, the power distribution is more controllable in the cases of Zr and Nb.

Evaluation of Sb-Nd and Te-Nd Phases within the U-Zr Fuel Matrix and Their Interactions with HT9 Alloy

An Alloying Element Screening Method to Design Zr2Co Based Alloys with Superior Disproportionation Resistance

Enhancing Disproportionation Resistance of Zr2Co-based Alloys by Regulating the Binding Energy of H Atom

Experimental and Theoretical Investigation on the Enhanced Hydrogen Storage Performance of Ti–Cr–Mn–Fe-Based Alloys Modified by Nb Substitution

Determining the effects of U/Pu ratio on subsolidus phase transitions in U-Pu-Zr metallic fuel alloys

Fuel-Clad Interactions: Uranium Nitride and Uranium Dioxide with FeCrAl and Ti-Modified Stainless Steel

Characterization of U–Nb–Zr dispersion fuel prepared by centrifugal atomization process

The Effect of Temperature and Burnup on U-10Zr Metallic Fuel Chemical Interaction with HT-9: a SEM-EDS Study

First-principles calculations to investigate mechanical, thermal, oxidation and hydrogen properties of Y, Zr and Nb alloyed U 3 Si 2

Early-stage Diffusion and Oxidation Behavior of Cr-Nb Coated Zr Alloy Accident Tolerant Fuel Cladding Materials at 1200°C - 1500°C

Reassessment of Oxidation-Induced Amorphization and Dissolution of Nb Precipitates in Zr−Nb Nuclear Fuel Cladding Tubes

A Study of the Effects of Hf and Sn on the Microstructure, Hardness and Oxidation of Nb-18Si Silicide-Based Alloys-RM(Nb)ICs with Ti Addition and Comparison with Refractory Complex Concentrated Alloys (RCCAs)

Addition of niobium in Fe-13Cr-4.5Al-2Mo alloy used as ATF cladding: Effect on high temperature water corrosion and in-situ electrochemistry

Effect of solute Nb and Sn on self-interstitial atom defect in zirconium-based alloys by first-principles calculations

Synergistic Effect of Zr and Ti on Microstructure and Properties for Nb Si Based In-Situ Composites

On the Microstructure and Properties of Nb-Ti-Cr-Al-B-Si-X (X = Hf, Sn, Ta) Refractory Complex Concentrated Alloys

Interface interactions in UN-X-UO2 systems (X = V, Nb, Ta, Cr, Mo, W) by pressure-assisted diffusion experiments at 1773 K

Advanced Characterization-Informed Framework and Quantitative Insight to Irradiated Annular U-10Zr Metallic Fuels

Thermo-mechanical behavior of hypoeutectic Ni-Y-Zr alloys

The possibility of utilizing novel cladding materials instead of zirconium in light water reactors

Influence of processing on secondary phase formation and microstructural evolution at U-10Mo alloy and Zr interlayer interfaces