Abstract:In this study, we conducted research on manufacturing molybdenum (Mo) thin films by a thermal atomic layer deposition method using solid MoO2Cl2 as a precursor. Mo thin films are widely used as gate electrodes and electrodes in metal-oxide semiconductor field-effect transistors. Tungsten (W) has primarily been used as a conventional gate electrode, but it suffers from reduced resistivity due to the residual fluorine component generated from the deposition process. Thus, herein, we developed a Mo thin film with low resistivity that can substitute W. The MoO2Cl2 precursor used to deposit the Mo thin film exists in a solid state. For solid precursors, the vapor pressure does not remain constant compared to that of liquid precursors, thereby making it difficult to set process conditions. Furthermore, the use of solid precursors at temperatures 600 °C and above has many limitations. Herein, H2 was used as the reactive gas for the deposition of Mo thin films, and the deposition temperature was increased to 650 °C, which was the maximum processing temperature of the aluminum nitride heater. Additionally, deposition rate, resistivity change, and surface morphology characteristics were compared. While resistivity decreased to 12.9 μΩ∙cm with the increase of deposition temperature from 600 °C to 650 °C, surface roughness (Rq) was increased to 0.560 nm with step coverage of 97%. X-ray diffraction analysis confirmed the crystallization change in the Mo thin film with increasing process temperature, and a certain thickness of the seed layer was required for nucleation on the initial wafer of the Mo thin film. Thus, the molybdenum nitride thin film was deposited after the 4 nm deposition of Mo thin film. This study confirmed that crystallinity of Mo thin films must be increased to reduce their resistivity and that a seed layer for initial nucleation is required.

Characterization of MoO3 and TixMoyOz Thin Films Prepared by Atomic Layer Deposition

Studying the Atomic Layer Deposition of Molybdenum Oxide and Titanium–Molybdenum Oxide Films Using Quartz Crystal Microbalance

Optical Properties of Al 2 O 3 Thin Film Fabricated by Atomic Layer Deposition

Constructing Conductive MoOx Thin Films by Plasma Enhanced Atomic Layer Deposition

Atomic layer deposition of crystalline molybdenum oxide thin films and phase control by post-deposition annealing

Optical, Optoelectronic, and Third‐Order Nonlinear Photonics of Ultrathin Molybdenum oxide Film Deposited by Atomic Layer Deposition

Mechanical and Optical Properties of Cr2O3 Thin Films Grown by Atomic Layer Deposition Method Using Cr(thd)3 and Ozone

Preparation and Characterization of Iron–molybdate Thin Films

Preferential Occupation of Molybdenum on the Thin Alumina Film: Characterization by CO Titration

Study on the Deposition Characteristics of Molybdenum Thin Films Deposited by the Thermal Atomic Layer Deposition Method Using MoO2Cl2 as a Precursor

Characterization and synthesis of cubic Zn2TiO4 crystalline films deposited on MgAl2O4 (100) substrates

Atomic layer deposition of molybdenum oxide using (N Bu)2(NMe2)2Mo, hydrogen peroxide (H2O2), and ozone (O3) for DRAM application

Atomic Layer Deposition of Molybdenum and Tungsten Oxide Thin Films Using Heteroleptic Imido-Amidinato Precursors: Process Development, Film Characterization, and Gas Sensing Properties

Atomic Layer Deposition of Co x O y Films: Oxidants versus Composition

Structural, Optical and Electrical Properties of Al+MoO3 and Au+MoO3 Thin Films Prepared by Magnetron Codeposition

Role of thermal heat-treatment to achieve a highly polycrystalline and compact α-MoO3 thin films

Structure and optical properties of TiO2 thin films deposited by ALD method

Plasma Enhanced Atomic Layer Deposition of Molybdenum Oxide from Mo(CO)6 and O2 Plasma for 2D Electronic Device Application

Thin Mno and Nio Films Grown Using Atomic Layer Deposition from Ethylcyclopentadienyl Type of Precursors

Substrate temperature-controlled precursor reaction mechanism of PEALD-deposited MoOx thin films