Abstract:The pulsed micro-discharge ablation source was applied to the optical spectra analysis of the aluminum alloy at atmospheric pressure. This needle-plane micro-discharge device has the merits of low cost, easy operation and fast analysis. Pulsed discharge allows large instantaneous input power without melting the sample, which is vital to keep the stability of the discharge. In the duration of a few microseconds, high voltage of about 4 000 V was applied to the tungsten needle electrode, which quickly initiates a discharge channel between the electrode and electrode, and results in current of 20 A between the tungsten needle tip and the sample. Thus, the sample was ablated before ablated particles were excited. The deposition energy, whose value was approximately 8.5 mJ per discharge pulse, was transmitted between the two discharge electrodes by means of the electric current. The surface morphology of the ablation crater generated by this pulsed needle-plane discharge indicated that a local micro-plasma was formed in the electrode gap. In addition, the on-axial energy flux and current density were much higher than those of the off-axis region. In order to further investigate the ablation mechanisms and physical properties, the electrical characteristic of this plasma source was discussed. The time evolution process of the discharge plasma was studied through precise timing shooting technique. From the fast imaging results of the ICCD camera, it could be seen that the lifetime of the plasma source was comparable with the pulse width of the high-voltage discharge source, and what was more, the change of optical intensity of plasma source showed good agreement with the variation of discharge current. Combined with an optical spectrometer, the pulsed micro-discharge ablation source could well excite atomic lines of aluminum, magnesium, manganese, bronze, and more in the alloy sample. The spectral characteristics of the discharge plasma were studied further. The electron excitation temperature of the discharge plasma was determined as about 6 700 K and the electron number density was obtained in the order of 10(17) cm(-3) using the Boltzmann plot method and Stark broadening of line, respectively. Besides, it was verified that the discharge plasma generated in this experiment was in local thermal equilibrium state. A further attempt was made to demonstrate the ability of this technique in quantitative analysis. Our results showed that the pulse micro-discharge plasma employed as spectral analysis source was an effective method for the quantitative analysis of aluminum alloy sample.

Effects of Anode Geometry on Analytical Performance of Solution Cathode Glow Discharge for Detection of Alkali Metals by Atomic Emission Spectroscopy

Determination of Metals in Environmental Waters by Solution Cathode Glow Discharge -Atomic Emission Spectroscopy (SCGD-AES) with a Syringe Pump for Sample Introduction

Analysis of metal elements by solution cathode glow discharge-atomic emission spectrometry with a modified pulsation damper

Highly Sensitive Determination of Cadmium by Atomic Emission Spectrometry with Miniaturized Solution Anode Glow Discharge

Multi-element Simultaneous sensitization of solution cathode glow discharge atomic emission spectrometry by using portable semiconductor anode refrigeration

Determination of Metal by Liquid Electrode Discharge Atomic Emission Spectrometry with A New Design

Solution Cathode Glow Discharge Based on Charge Coupled Device Detector

Solution Cathode Glow Discharge – Atomic Emission Spectrometry (SCGD-AES) With an Interference Filter for Spectral Discrimination for the Determination of Thallium in Surface Water

Detection of Metal Residue in Aqueous Solutions by Electrolyte Cathode Atmospheric Glow Discharge Emission Spectroscopy

Comprehensive evaluation of matrix effect in the detection of Zn, Cd, Ni, Cu, Cr and Pb by solution cathode glow discharge optical emission spectrometry

Experimental and Analytical Study on Electrolytic Decomposition of HAN-water Solution Using Graphite Electrodes

Solution-Based Glow Discharges for Atomic Emission Spectroscopy Come of Age

Investigation on robustness of Nanosized-Scandia Doped Dispenser Cathodes

Sensitivity improvement of solution cathode glow discharge-optical emission spectrometry by external magnetic field for optical determination of elements

Analysis of Trace Heavy Metal in Solution Using Liquid Cathode Glow Discharge Spectroscopy

[Determination of Alkali-Earth Metal by Microwave Plasma Torch Atomic Emission Spectrometry].

Direct Determination of Trace Amounts of Acetic Acid Using a Novel Ambient Glow Discharge Ion Source

Cathode etching phenomenon of high beam-anode ion source and its elimination measures

Elemental Analysis of Alloy Sample with Pulsed Micro-Discharge Optical Emission Spectrometry

Ultra-sensitive determination of inorganic arsenic valence by solution cathode glow discharge-atomic emission spectrometry coupled with hydride generation

Investigation of Nanosized-Scandia-Doped Dispenser Cathodes with Machined Surfaces