Abstract:Experiments and numerical simulations have been done to investigate the heat transfer, pressure loss and turbulent flow characteristics over the surfaces with arrays of shallow dimples of different dimple depths within channels. Three different dimple depth to diameter ratios of 0.067, 0.1 and 0.2 are investigated with the Reynolds number (Re) ranging from 10,000 to 60,000. Heat transfer measurements were done by using the transient liquid crystal thermography technique to obtain the local heat transfer enhancement characteristics. Additional steady-state experiments were also done to obtain the overall heat transfer enhancement and the pressure loss of the turbulent flow over the dimpled surfaces. The experimental results indicated that the dimple depth has appreciable effects on heat transfer enhancement and pressure loss. The Reynolds number also shows appreciable effects on the local heat transfer enhancement distribution on the surface with shallower dimples. The overall heat transfer enhancement of all the dimpled surfaces approximately keep constant with the Reynolds numbers. The experiments still indicate that the shallow dimples with the depth to diameter ratio of 0.067 obtained almost constant overall heat transfer enhancement up to 1.4 with negligible pressure loss penalty, which indicates a high and constant Reynolds analogy factor of about 1.33 over the studied Reynolds number range. However, as the dimple depth ratio increases from 0.067 to 0.2, the pressure loss increases rapidly and surpasses the heat transfer enhancement, which leads to lower Reynolds analogy factor than 1.0. Furthermore, the numerical simulations show detailed turbulent flow characteristics over the dimpled surfaces. Different from the dimples with relatively deep depth ratios of 0.1 and 0.2, the shallower dimples with the depth ratio of 0.067 generate an obvious low-speed swirling horseshoe vortex zone near the upstream rim in the dimples at the relatively high Reynolds number of 50,500. The horseshoe vortex shed from spanwise edges of the shallow dimples produces lower but more uniform turbulent mixing intensity in the near-wall region, which is responsible for the higher thermal performance.

Thermo-hydraulic performance inside convergent rectangle channel with large-deformed dimples

The Structural Optimization of Dimple in Microchannel for Heat Transfer Enhancement

Numerical Study of Heat Transfer and Flow Structure over Channel Surfaces Featuring Miniature V Rib-Dimples with Various Configurations

Influence of Dimple Diameter and Depth on Heat Transfer of Impingement-Cooled Turbine Leading Edge with Cross-Flow and Dimple

Experimental Study on Flow Behavior and Heat Transfer Enhancement With Distinct Dimpled Gas Turbine Blade Internal Cooling Channel

Heat Transfer Enhancement In A Rectangular Channel With The Combination Of Ribs, Dimples And Protrusions

A Hybrid V-shaped and Spherical Dimple Structure in a Rectangular Channel for Enhancing the Thermal-Hydraulic Performance

An Experimental Investigation on the Flow Characteristics Over Dimple Arrays Pertinent to Internal Cooling of Turbine Blades

Numerical Study on Flow and Heat Transfer Performance of Rectangular Heat Sink with Compound Heat Transfer Enhancement Structures

Numerical Investigation on Heat Transfer Performance and Flow Characteristics in a Rectangular Air Cooling Channel (AR = 2) with Ridged Dimples

A Numerical Study of the Flow and Heat Transfer in the Pin Fin-Dimple Channels with Various Dimple Depths

Numerical Investigation of Flow and Heat Transfer in Rotating Trapezoidal Channel with Lateral Slots and Dimple Structure

Experimental Study and Numerical Analysis of Heat Transfer Enhancement and Turbulent Flow over Shallowly Dimpled Channel Surfaces

A Numerical Investigation of Dimple Effects on Internal Heat Transfer Enhancement of A Double Wall Cooling Structure with Jet Impingement

Experimental Study of Heat Transfer and Pressure Loss in Channels with Miniature V Rib-Dimple Hybrid Structure

Rotating Cooling Performance of Two-Pass Rectangular Channels With Cross Bridge and Oval-Shaped Dimple

Experimental and Numerical Study of Heat Transfer and Flow Friction in Channels with Dimples of Different Shapes

Numerical Predictions on Fluid Flow and Heat Transfer in U-Shaped Channel with the Combination of Ribs, Dimples and Protrusions under Rotational Effects

The Effect of Dimple/protrusion Arrangements on the Comprehensive Thermal Performance of Variable Cross-Section Rotating Channels for Gas Turbine Blades

Effect of dimple edge ratio on the thermo-aerodynamic performance in turbulent channel flow

Effect of Bleed Hole on Flow and Heat Transfer Performance of U-Shaped Channel with Dimple Structure