Abstract:Metal mesh foil bearings (MMFBs), simple to construct and inexpensive, are a promising bearing technology for oil-free microturbomachinery operating at high speed and high temperature. Prior research demonstrated the near friction-free operation of a MMFB operating to 60 krpm and showing substantial mechanical energy dissipation characteristics. This paper details further experimental work and reports MMFB rotordynamic force coefficients. The test rig comprises a turbocharger driven shaft and overhung journal onto which a MMFB is installed. A soft elastic support structure akin to a squirrel cage holds the bearing, aiding to its accurate positioning relative to the journal. Two orthogonally positioned shakers excite the test element via stingers. The test bearing comprises a cartridge holding a Copper wire mesh ring, 2.7 mm thick, and a top arcuate foil. The bearing length and inner diameter are 38 mm and 36.5 mm, respectively. Experiments were conducted with no rotation and with journal spinning at 40–50 krpm, with static loads of 22 N and 36 N acting on the bearing. Dynamic load tests spanning frequencies from 150 to 450 Hz were conducted while keeping the amplitude of bearing displacements at 20 μm, 25 μm, and 30 μm. With no journal spinning, the force coefficients represent the bearing elastic structure alone because the journal and bearing are in contact. The direct stiffnesses gradually increase with frequency while the direct damping coefficients drop quickly at low frequencies (< 200 Hz) and level off above this frequency. The damping combines both viscous and material types from the gas film and mesh structure. Journal rotation induces airborne operation with a hydrodynamic gas film separating the rotor from its bearing. Hence, cross-coupled stiffness coefficients appear although with magnitudes lower than those of the direct stiffnesses. The direct stiffnesses, 0.4 to 0.6 MN/m within 200–400 Hz, are slightly lower in magnitude as those obtained without journal rotation, suggesting the air film stiffness is quite high. Bearing direct stiffnesses are inversely proportional to the bearing motion amplitudes, whereas the direct equivalent viscous damping coefficients do not show any noticeable variation. All measurements evidence a test bearing system with material loss factor (γ) ∼ 1.0, indicating significant mechanical energy dissipation ability.

Elastic and damping characterization of open-pore metal foams filled or not with an elastomer for vibration control in turbomachinery

Static and Dynamic Behavior of PU Foams with Multilayer Coatings

Stiffness, Energy Dissipation, and Hyperelasticity in Hierarchical Multilayer Composite Nanocoated Open‐Cell Polyurethane Foams

Metal Mesh Foil Bearing: Effect of Motion Amplitude, Rotor Speed, Static Load, and Excitation Frequency on Force Coefficients

Towards Highly Efficient, Additively Manufactured Passive Vibration Eliminators for Mechanical Systems

A Double Degree Freedom Mass-Spring-Damper-Foam Collision Model for High Porosity Metallic Foams

Elastomer Composites with High Damping and Low Thermal Resistance via Hierarchical Interactions and Regulating Filler

Study on Damping Behavior of Foamed Aluminum with Macroscopic Pores

Experimental Study on the Vibration Reduction Performance of the Spindle Rotor of a Rubbing Machine Based on Aluminium Foam Material

Impact of damping on decay time of free oscillations in metal structures

Performance evaluation of extruded polystyrene foam for aerospace engineering applications using frequency analyses

Crush behaviour and vibration damping properties of syntactic foam incorporating waste tyre-derived crumb rubber

Influence of density and loading speed on static and impact properties of closed-cell metallic foams

Re-Design of Machine Tool Joint Components Based on Polymer Fillings for High-Speed Performance

Escaping the Ashby limit for mechanical damping/stiffness trade-off using a constrained high internal friction interfacial layer

High fidelity simulation of the mechanical behavior of closed-cell polyurethane foams

Preload Influence on the Dynamic Properties of a Polyurethane Elastomeric Foam

Effects of bearing clearance and supporting stiffness on performances of rotor-bearing system with multi-decked protuberant gas foil journal bearing

Hyperelastic Material Parameter Determination and Numerical Study of TPU and PDMS Dampers

Vibration Damping Properties of Gradient Polyurethane/vinyl Ester Resin Interpenetrating Polymer Network

Assessment of frequency and amplitude dependence on the cyclic degradation of polyurethane foams