Abstract:High specific strength and superior corrosion resistance are two key characteristics of the aerospace grade AA7075-T6 alloy. However, the surface behavior of AA7075-T6 is found to be deprived, because of its behavior of being prone to fretting fatigue and adhesive wear under dry sliding conditions. Thus, surface wear behavior improvement with the retention of the microhardness of the alloy is required for increasing its wider application. For this, surface isomorphous precipitates and the soft matrix need to be protected through dispersion of hard thermally stable ceramic SiC with solid-lubricant graphite particles. The dispersion through friction stir processing (FSP) avoids detrimental phase formations by processing the metal alloy below its melting point temperature. Thus, dispersion of SiC-Graphite inside the AA7075-T6 using FSP is the focal point of the study. The low and high wear rate samples have been analyzed using SEM imaging and elemental analysis through XRD and EDS mapping. In this study, reinforcing the SiC-Gr particles greatly improved the wear behavior of the AA7075 alloy. Wear resistance has been controlled by combining soft solid lubricant Gr particles with load-bearing hard SiC nanoparticles. In dry sliding action, the base alloy matrix was severely exposed to wear, but the hard SiC nanoparticles served as load-bearing asperities and improved the wear resistance. Simultaneously, the graphite layers generated the soft solid lubricating tribofilm further to reduce the wear and friction between mating surfaces. The wear mechanisms have changed prominently from adhesion to abrasion and delamination through reinforcing the SiC-Gr reinforcements. The graphite content in a hybrid ratio with SiC hard particles was found to have improved the wear resistance by 78%. The tendency of fatigue was more effectively improved in surface composites as compared to the base alloy.

Investigation of aluminum-based mono and hybrid surface composites by incorporating SiC and graphene reinforcements using friction stir processing

Development of Al-Mg2Si Alloy Hybrid Surface Composites by Friction Stir Processing: Mechanical, Wear, and Microstructure Evaluation

Wear Analysis of Friction Stir Processed AA7075-SiC-Graphite Hybrid Surface Composites

Wear Characteristics of Al5083 Surface Hybrid Nano-composites by Friction Stir Processing

Microstructure and mechanical characteristics of Al1050/B2O3+Cu hybrid surface nanocomposite fabricated using friction stir processing

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Al-5052/SiC + CeO 2 hybrid surface composites: Achieving improved microstructural and mechanical behaviour via friction stir processing

Microstructural Evolution & Mechanical Properties of ZrO2/GNP and B4C/GNP reinforced AA6061 Friction Stir Processed Surface Composites - A Comparative study

Experimental and numerical investigation of multiwalled carbon nanotube/aluminosilicate reinforced aluminum hybrid surface composites using friction stir processing

Wear and mechanical properties of surface hybrid metal matrix composites on Al–Si aluminum alloys fabricated by friction stir processing

Microstructure and Mechanical Properties of SiC + Fe + Mn + Sn Hybrid Reinforced Surface Composites Fabricated by Friction Stir Processing: Effect of Double Pass

Synthesis and characterization of AA7075/SiC/graphene hybrid composite

Implications of nanomaterials reinforcement along with sub-zero temperature cooling on microstructure and mechanical properties of friction stir processed Al7075 alloy

The Effect of Mono and Hybrid Additives of Ceramic Nanoparticles on the Tribological Behavior and Mechanical Characteristics of an Al-Based Composite Matrix Produced by Friction Stir Processing

Fabrication of Al6061/Ti 3 AlC 2 MAX phase surface composite by friction stir processing and investigation of wear properties

Effect of Microstructure on Mechanical Behaviors of Al6061 Metal Matrix Composite Reinforced with Silicon Nitride (Si3N4) and Silicon Carbide (SiC) Micro Particles

Evaluating the influence of various friction stir processing strategies on surface integrity of hybrid nanocomposite Al6061

Characterization of Al 5052 Based Metal Matrix Composites Reinforced with SiC and Al2O3

Synergistic effect of hybrid reinforcement on magnesium-based composites for enriching mechanical and tribological characteristics

Optimizing friction stir processing parameters for aluminium alloy 2024 reinforced with SiC particles: A taguchi approach of investigation

Investigating the Effect of Particle Sizes of SiC and Graphite on Strengthening of Aluminium Metal Matrix Composites