Abstract:High specific strength and superior corrosion resistance are two key characteristics of the aerospace grade AA7075-T6 alloy. However, the surface behavior of AA7075-T6 is found to be deprived, because of its behavior of being prone to fretting fatigue and adhesive wear under dry sliding conditions. Thus, surface wear behavior improvement with the retention of the microhardness of the alloy is required for increasing its wider application. For this, surface isomorphous precipitates and the soft matrix need to be protected through dispersion of hard thermally stable ceramic SiC with solid-lubricant graphite particles. The dispersion through friction stir processing (FSP) avoids detrimental phase formations by processing the metal alloy below its melting point temperature. Thus, dispersion of SiC-Graphite inside the AA7075-T6 using FSP is the focal point of the study. The low and high wear rate samples have been analyzed using SEM imaging and elemental analysis through XRD and EDS mapping. In this study, reinforcing the SiC-Gr particles greatly improved the wear behavior of the AA7075 alloy. Wear resistance has been controlled by combining soft solid lubricant Gr particles with load-bearing hard SiC nanoparticles. In dry sliding action, the base alloy matrix was severely exposed to wear, but the hard SiC nanoparticles served as load-bearing asperities and improved the wear resistance. Simultaneously, the graphite layers generated the soft solid lubricating tribofilm further to reduce the wear and friction between mating surfaces. The wear mechanisms have changed prominently from adhesion to abrasion and delamination through reinforcing the SiC-Gr reinforcements. The graphite content in a hybrid ratio with SiC hard particles was found to have improved the wear resistance by 78%. The tendency of fatigue was more effectively improved in surface composites as compared to the base alloy.

Wear Characteristics of Al5083 Surface Hybrid Nano-composites by Friction Stir Processing

Wear Analysis of Friction Stir Processed AA7075-SiC-Graphite Hybrid Surface Composites

Fabrication of Al6061/Ti 3 AlC 2 MAX phase surface composite by friction stir processing and investigation of wear properties

Investigation of aluminum-based mono and hybrid surface composites by incorporating SiC and graphene reinforcements using friction stir processing

Development of Al-Mg2Si Alloy Hybrid Surface Composites by Friction Stir Processing: Mechanical, Wear, and Microstructure Evaluation

Microstructural Evolution & Mechanical Properties of ZrO2/GNP and B4C/GNP reinforced AA6061 Friction Stir Processed Surface Composites - A Comparative study

Utilizing Additive Friction Stir Processing to Fabricate B4C Reinforced Ti–6Al–4V Matrix Surface Composite: Microstructure Refinement and Enhancement in Mechanical Properties

Microstructure and mechanical characteristics of Al1050/B2O3+Cu hybrid surface nanocomposite fabricated using friction stir processing

Nanoarchitectonics of AA7075-NbC Surface Composites for Augmenting the Mechanical and Tribological Properties

Experimental and numerical investigation of multiwalled carbon nanotube/aluminosilicate reinforced aluminum hybrid surface composites using friction stir processing

A study on microstructural, mechanical properties, and optimization of wear behaviour of friction stir processed AZ31/TiC composites using response surface methodology

Modeling of wear performance and surface roughness of AA6061-T6/B4C composite under dry sliding conditions by RSM

Influence of heat treatment on the microstructure, mechanical and tribological performances of particle reinforced aluminum matrix surface composite fabricated through friction stir processing

The effect of friction stir processing on mechanical, wear and corrosion characteristics of Cu-AlN-BN surface composite

Fabrication of in Situ Carbon Fiber/aluminum Composites Via Friction Stir Processing: Evaluation of Microstructural, Mechanical and Tribological Behaviors

Implications of nanomaterials reinforcement along with sub-zero temperature cooling on microstructure and mechanical properties of friction stir processed Al7075 alloy

Microstructure, hardness, and wear resistance of AA5083/Ti3SiC2 composites fabricated via friction stir processing

Wear and mechanical properties of surface hybrid metal matrix composites on Al–Si aluminum alloys fabricated by friction stir processing

Tribological Characteristics of Al359/Si3N4/Eggshell Surface Composite Produced by Friction Stir Processing

Development of Cu-(Gr + W) Hybrid Surface Composites Fabricated through Friction Stir Processing

The Effect of Mono and Hybrid Additives of Ceramic Nanoparticles on the Tribological Behavior and Mechanical Characteristics of an Al-Based Composite Matrix Produced by Friction Stir Processing