Abstract:The deposition parameters used during the sputtering process are instrumental in determining the properties of the deposited films and can be optimised to produce thin film coatings that are suitable for specific engineering applications. Deposition parameters such as radio frequency (RF) power, oxygen flow rate, and substrate temperature can be varied during deposition to alter or tune the film structure, stoichiometry, and invariably the functional properties of the prepared thin films. In this paper, chromium oxide thin films prepared by reactive magnetron sputtering under various RF powers were characterised for their work function property and stability in Ringer's solution. The structural, oxide phase and growth modes of the films were probed with X-ray diffraction (XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and scanning electron microscope (SEM). The electrochemical stability and corrosion behaviour of the films were evaluated using an open circuit potential (OCP) measurements, cyclic polarisation, and Mott–Schottky analysis, while the work function (WF) was determined with a Kelvin probe. The XRD and Raman investigations showed that the films are predominantly amorphous with Cr 2 O 3 being the main oxide phase. A mixture of columnar and layer-by-layer growth modes was observed in the deposited films with 500 W, 10 sccm sample showing rougher morphology due to the higher sputtering power. The OCP and cyclic polarisation results showed that the film prepared at a deposition power of 300 W and at an oxygen flow rate of 10 sccm possesses higher film passivation and breakdown potentials, hence, better corrosion resistance when compared to films prepared at higher deposition powers. The finding is further supported by the Mott–Schottky and work function investigations where the same film also showed lower defect density and higher work function values compared to the films deposited at higher powers. A correlation was found between the corrosion, work function and defect density which suggests that both parameters can possibly be used to predict and rank corrosion in thin films. We expect our findings to be significant for future corrosion and wear applications for metals/alloys requiring protection against environmental degradation.

Stability of trivalent and hexavalent chromium oxide layers on aluminum substrates from electronic structure calculations

Investigation of the trivalent-chrome coating on 6063 aluminum alloy

Chromate Formed in a Trivalent Chromium Conversion Coating on Aluminum

Aluminum concentration effect on the oxidation behavior of CrAl coatings investigated by high-throughput method

High-temperature stability and leaching kinetics of the hexavalent chromium compound, chrome-hauyne (Ca4Al6CrO16)

The Effect of Chromium on the Gamma to Alpha Phase Transition of Alumina Coating Formed on 316L SS by a Cathodic Micro Arc Deposition (CMAD) Process

Atomic layer deposition of chromium oxide—An interplay between deposition and etching

Effects of Chromium on the Oxidation Performance of β-FeAlCr Coatings

Characterization of oxides formed on iron-chromium-aluminum alloy in simulated light water reactor environments

Effects Of Chromium On The Oxidation Performance Of Beta-Fealcr Coatings

Effect of Alkaline Etching on Formation Behavior and Corrosion Resistance of a Cr-Zr-Ti TCP Conversion Coating on AA2024 Aluminum Alloy

Corrosion Susceptibility of Passive Films on 1060, 2024, and 5083 Aluminum Alloys: Experimental Study and First-Principles Calculations

Understanding Ion Transport Mechanisms of Chromium-Coated Zirconium Alloy Cladding in Steam Oxidation

An investigation of the work function and stability of chromium oxide thin films deposited by reactive magnetron sputtering

Chemical Stability of Chromium Oxide Films Formed by MOCVD in Subcritical and Supercritical Water

Effects of Al addition on high temperature oxidation behavior of 16Cr ODS steel

Chemomechanical Finite Element Analysis for Surface Oxidation of Aluminum Alloy

Comparisons of Air and Water Oxidation on the Passive Properties of Chromium

Modelling compositional changes in nickel base alloy 602 CA during high temperature oxidation

Incipient Corrosion of FeCrAl Alloys in H3BO3- and LiOH-containing Pure Water at 360 °C and 18.5 MPa

How solute atoms control aqueous corrosion of Al-alloys