Abstract:Ni-rich layered cathode materials are important candidates for lithium-ion batteries used for high energy density applications, such as electric vehicles. However, these materials are suffering severe capacity fade caused by surface reconstruction, unstable cathode-electrolyte interface (CEI) formation and micro crack formation during cycling, especially when a high cut off charge voltage is applied (such as 4.6 and 4.8V). To understand the origin of this capacity fade, state-of-the-art diagnostic tools are applied to understand their structure, chemical and morphological properties of LiNi0.94Co0.06O2 (NC) and LiNi0.92Co0.06Al0.02O2 (NCA) cathode materials during cycling. Electrochemical measurement results show that the NCA cathode delivered higher capacity and stable cyclic performance even cycled at a high cut of voltage of 4.8V. In situ X-ray absorption spectroscopy (XAS) results of NC and NCA electrodes measured during the first and 51st charge/discharge cycling between the voltage range of 2.8-4.4V showed that both Ni and Co contribute to the capacity by going through the Ni3+/Ni4+ and Co3+/Co4+ redox couples. The Ni-K edge XAS spectra of NC cathode charged to 4.8V showed slightly reduction of Ni4+ during the high voltage charging. While, XAS spectra of NCA cathode did not showed reduction of Ni4+ when the cell charged to the higher voltage. More interestingly, C, F, O, Ni and Co soft XAS spectroscopy of NC and NCA electrodes at the different state of charge provided more comprehensive insight into surface and bulk chemical properties. The results showed that much thicker CEI layer formed on the NC surface compared with the NCA cathode, indicated that Al-doping effectively reduced the side reaction of cathode materials with the electrolyte. We have also compared the morphological and chemical evolution of NC and NCA secondary particles using full-filed in-situ transmission X-ray microscopy (TXM) during the initial cycle. Results will be presented at the meeting. Acknowledgement This project was supported by the U.S. Department of Energy, the Assistant Secretary for Energy Efficiency and Renewable Energy, Office of Vehicle Technologies through Advanced Battery Material Research (BMR) program (Battery500 consortium) under Contract No. DESC0012704.

Insight into the Surface Reconstruction-Induced Structure and Electrochemical Performance Evolution for Ni-Rich Cathodes with Postannealing after Washing

Realizing Superior Cycling Stability of Ni-Rich Layered Cathode by Combination of Grain Boundary Engineering and Surface Coating

Unveiling the parasitic-reaction-driven surface reconstruction in Ni-rich cathode and the electrochemical role of Li2CO3

Near-surface reconstruction in Ni-rich layered cathodes for high-performance lithium-ion batteries

Robust Surface Reconstruction Induced by Subsurface Ni/Li Antisites in Ni-Rich Cathodes

Surface reconstruction and chemical evolution of stoichiometric layered cathode materials for lithium-ion batteries

Stabilizing surface chemical and structural Ni-rich cathode via a non-destructive surface reinforcement strategy

Lithium‐Ion Batteries: Cooling Induced Surface Reconstruction during Synthesis of High‐Ni Layered Oxides (Adv. Energy Mater. 43/2019)

Enhancing the Cycling and Rate Performance of Ni-Rich Cathodes for Lithium-Ion Batteries by Bulk-Phase Engineering and Surface Reconstruction

Surface Reconstruction of Ni‐Rich Layered Cathodes: in Situ Doping Versus Ex Situ Doping

Unveiling Surface Reconstruction as the Primary Trigger for Capacity Loss in Ultra‐High Nickel Cathodes

Electrochemical Evolution of the Surface and Subsurface Properties of Layered Nickel-Rich Oxide Cathodes

A New Insight into the Capacity Decay Mechanism of Ni‐Rich Layered Oxide Cathode for Lithium‐Ion Batteries

Surface Surgery of the Nickel-Rich Cathode Material LiNi0.815Co0.15Al0.035O2: Toward a Complete and Ordered Surface Layered Structure and Better Electrochemical Properties

Degradation Mechanism of Ni-Rich Layered Cathode Materials During High Voltage Cycling Revealed by Multi-Model Synchrotron X-Ray Imaging and Spectroscopy Techniques

Boosting Cell Performance of LiNi 0.8 Co 0.15 Al 0.05 O 2 via Surface Structure Design.

The Role of Secondary Particle Structures in Surface Phase Transitions of Ni-Rich Cathodes

Surface In-Situ Reconstruction of LiNi0.8Co0.1Mn0.1O2 Cathode Materials Interacting with Antimony Compounds and the Electrochemical Performances

Bulk Fatigue Induced by Surface Reconstruction in Layered Ni-rich Cathodes for Li-ion Batteries

New insights into dry-coating-processed surface engineering enabling structurally and thermally stable high-performance Ni-rich cathode materials for lithium ion batteries

Surface Reconstruction of High-Voltage LiNi0.5Mn1.5O4 Cathode via the Sculpture Method toward Enhanced Stability