Abstract:Ni-rich layered cathode materials are important candidates for lithium-ion batteries used for high energy density applications, such as electric vehicles. However, its capacity fades during cycling, especially when a high cut off charge voltage is applied (>4.4 V). To understand the origin of this capacity fade, comprehensive diagnostic tools are applied to understand their structure, chemical and morphological properties during cycling. X-ray diffraction results show that while the LiNi0.6Mn0.2Co0.2O2 (NMC622) can mostly recover its original structure at fully discharged state, even after 0.95 Li is extracted (charged to 5.2 V), it does undergo slab sliding that leads to stacking fault (O1 type) which does not go away during cycling. In addition, transmission X-ray imaging (TXM) results indicate that cycling can induces Li content inhomogeneity within the particle. As a result, the strain builds up and is directly responsible for the cracking of primary and secondary particles. Hard X-ray absorption spectroscopy (XAS) results indicate that both Ni and Co contribute to the capacity by going through the Ni3+/Ni4+ and Co3+/Co4+ redox couples. A comparison is made between Ni-rich and the Li-rich layered materials, which is well known for the problem of oxygen release. It is found that for the Ni-rich system, the oxidization state of transition metals (bulk) are well maintained during cycling, whereas for the Li-rich system the average oxidization states keep decreasing (lower oxidation states at both fully charged and fully discharged states after cycling than the pristine sample), suggesting at least the bulk of Ni-rich material is robust against oxygen release. Soft XAS that differentiates the surface chemical information from the bulk indicates that inactive rock salt phase is formed during cycling. These results show that cycling induced strain, stacking fault and surface reconstruction are the main issues to be addressed for further improvement of this material. Acknowledgement This project was supported by the U.S. Department of Energy, the Assistant Secretary for Energy Efficiency and Renewable Energy, Office of Vehicle Technologies through Advanced Battery Material Research (BMR) program (Battery500 consortium) under Contract No. DESC0012704. This research used resources 8-ID and 28-ID-2 of the National Synchrotron Light Source II, a U.S. Department of Energy (DOE) Office of Science User Facility operated for the DOE Office of Science by Brookhaven National Laboratory under contract no. DE-SC0012704. The authors would also like to acknowledge the use of beamline 6-2c of Stanford Synchrotron Radiation Lightsource, SLAC National Accelerator Laboratory, supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences under contract no. DE-AC02-76SF00515.

Rational design of surface reconstruction with pinning effect to relieving bulk fatigue for high energy single-crystal Ni-rich cathodes

Well-dispersed single-crystalline nickel-rich cathode for long-life high-voltage all-solid-state batteries

Bulk Fatigue Induced by Surface Reconstruction in Layered Ni-rich Cathodes for Li-ion Batteries

Structural self-reconstruction strategy empowering Ni-rich layered cathodes with low-strain for superior cyclabilities

Atomical Reconstruction and Cationic Reordering for Nickel‐Rich Layered Cathodes

Surface Reconstruction Reduces Internal Stress of Ni-Rich Cathode Particles.

Insight into the Capacity Degradation and Structural Evolution of Single-Crystal Ni-rich Cathodes

Surface Regulation Enables High Stability Of Single-Crystal Lithium-Ion Cathodes At High Voltage

Reducing structural degradation of high-voltage single-crystal Ni-rich cathode through in situ doping strategy

Gradient Boracic Polyanion Doping-Derived Surface Lattice Modulation of High-Voltage Ni-Rich Layered Cathodes for High-Energy-Density Li-Ion Batteries

Reversibility of Ni-Rich Layered Cathode Material Revealed by Structural, Spectroscopic and Imaging Characterizations

Targeted Doping Enables Multi-Scale Stress Regulation for High Reliable Ni-Rich Layered Cathodes

Achieving Long‐Life Ni‐Rich Cathodes with Improved Mechanical‐Chemical Properties Via Concentration Gradient Structure

Enhancing chemomechanical stability and high-rate performance of nickel-rich cathodes for lithium-ion batteries through three-in-one modification

Mitigating the Surface Reconstruction of Ni-Rich Cathode <i>via</i> P2-Type Mn-Rich Oxide Coating for Durable Lithium Ion Batteries

Chemical-Mechanical Effects in Ni-Rich Cathode Materials

Superior Fast-Charging Ni-rich Cathode Via Promoted Kinetic-Mechanical Performance

One-step Surface-to-bulk Modification of Single-Crystalline Ni-rich Co-poor Cathodes for High-Rate and Long-Life Li-ion Batteries at High-Voltage Operations

Single-Crystalline Ni-Rich layered cathodes with Super-Stable cycling

Synergistic Regulation of Kinetic Reaction Pathway and Surface Structure Degradation in Single-Crystal High-Nickel Cathodes

Structure and Charge Regulation Strategy Enabling Superior Cyclability for Ni‐Rich Layered Cathode Materials