Abstract:Ni-rich layered cathode materials are important candidates for lithium-ion batteries used for high energy density applications, such as electric vehicles. However, its capacity fades during cycling, especially when a high cut off charge voltage is applied (>4.4 V). To understand the origin of this capacity fade, comprehensive diagnostic tools are applied to understand their structure, chemical and morphological properties during cycling. X-ray diffraction results show that while the LiNi0.6Mn0.2Co0.2O2 (NMC622) can mostly recover its original structure at fully discharged state, even after 0.95 Li is extracted (charged to 5.2 V), it does undergo slab sliding that leads to stacking fault (O1 type) which does not go away during cycling. In addition, transmission X-ray imaging (TXM) results indicate that cycling can induces Li content inhomogeneity within the particle. As a result, the strain builds up and is directly responsible for the cracking of primary and secondary particles. Hard X-ray absorption spectroscopy (XAS) results indicate that both Ni and Co contribute to the capacity by going through the Ni3+/Ni4+ and Co3+/Co4+ redox couples. A comparison is made between Ni-rich and the Li-rich layered materials, which is well known for the problem of oxygen release. It is found that for the Ni-rich system, the oxidization state of transition metals (bulk) are well maintained during cycling, whereas for the Li-rich system the average oxidization states keep decreasing (lower oxidation states at both fully charged and fully discharged states after cycling than the pristine sample), suggesting at least the bulk of Ni-rich material is robust against oxygen release. Soft XAS that differentiates the surface chemical information from the bulk indicates that inactive rock salt phase is formed during cycling. These results show that cycling induced strain, stacking fault and surface reconstruction are the main issues to be addressed for further improvement of this material. Acknowledgement This project was supported by the U.S. Department of Energy, the Assistant Secretary for Energy Efficiency and Renewable Energy, Office of Vehicle Technologies through Advanced Battery Material Research (BMR) program (Battery500 consortium) under Contract No. DESC0012704. This research used resources 8-ID and 28-ID-2 of the National Synchrotron Light Source II, a U.S. Department of Energy (DOE) Office of Science User Facility operated for the DOE Office of Science by Brookhaven National Laboratory under contract no. DE-SC0012704. The authors would also like to acknowledge the use of beamline 6-2c of Stanford Synchrotron Radiation Lightsource, SLAC National Accelerator Laboratory, supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences under contract no. DE-AC02-76SF00515.

Unveiling Surface Reconstruction as the Primary Trigger for Capacity Loss in Ultra‐High Nickel Cathodes

Revealing Two Distinctive Intergranular Cracking Mechanisms of Ni-rich Layered Cathode by Cross-Sectional Scanning Electron Microscopy

Insight into the capacity decay mechanism of cycled LiNi 0.5 Co 0.2 Mn 0.3 O 2 cathodes via in situ x-ray diffraction

Intergranular Cracking As a Major Cause of Long-Term Capacity Fading of Layered Cathodes.

High‐Voltage Charging‐Induced Strain, Heterogeneity, and Micro‐Cracks in Secondary Particles of a Nickel‐Rich Layered Cathode Material

The Role of Secondary Particle Structures in Surface Phase Transitions of Ni-Rich Cathodes

Bulk Fatigue Induced by Surface Reconstruction in Layered Ni-rich Cathodes for Li-ion Batteries

Surface Reactivity Versus Microcracks in Ni-Rich Layered Oxide Cathodes: Which is Critical for Long Cycle Life?

Insight into the Surface Reconstruction-Induced Structure and Electrochemical Performance Evolution for Ni-Rich Cathodes with Postannealing after Washing

Insight into the Capacity Degradation and Structural Evolution of Single-Crystal Ni-rich Cathodes

Surface-dependent stress-corrosion cracking in Ni-rich layered oxide cathodes

Rational design of surface reconstruction with pinning effect to relieving bulk fatigue for high energy single-crystal Ni-rich cathodes

Degradation Mechanism of Ni-Rich Layered Cathode Materials During High Voltage Cycling Revealed by Multi-Model Synchrotron X-Ray Imaging and Spectroscopy Techniques

Modifying surface chemistry and stress concentration to enable highly stable ultrahigh-Ni cathodes

Surface Regulation Enables High Stability Of Single-Crystal Lithium-Ion Cathodes At High Voltage

Reversibility of Ni-Rich Layered Cathode Material Revealed by Structural, Spectroscopic and Imaging Characterizations

Bulk and surface degradation in layered Ni-rich cathode for Li ions batteries: Defect proliferation via chain reaction mechanism

Advancements in Addressing Microcrack Formation in Ni–Rich Layered Oxide Cathodes for Lithium–Ion Batteries

Real-Time Observation of Chemomechanical Breakdown in a Layered Nickel-Rich Oxide Cathode Realized by In Situ Scanning Electron Microscopy

Looking into Failure Mode Identification Driven by Differential Capacity in Ni-rich Layered Cathodes

Unraveling the nonlinear capacity fading mechanisms of Ni-rich layered oxide cathode