Abstract:Conductive copper nanoinks can be used as a low-cost replacement for silver and gold nanoinks that are used in inkjet printing of conductive patterns. We describe a high-throughput, simple, and convenient method for the preparation of copper nanoparticles in aqueous solution at room temperature. Copper acetate is used as the precursor, hydrazine as the reducing agent, and short chain carboxylic acids as capping agents. The concentration of the carboxylic acid plays a key role in the preparation of such copper nanoparticles. Stable copper nanoparticles with a diameter of less than 10 nm and a narrow size distribution were prepared when high concentrations of lactic acid, citric acid, or alanine were used. Thermogravimetric analysis results showed that any lactic acid or glycolic acid adsorbed on the surface of the copper nanoparticles can be removed at a relatively low temperature, especially, glycolic acid, which can be removed from the surface at about 125 °C. Highly conductive copper films prepared using lactic acid and glycolic acid as capping agents were obtained by drop coating a copper nanoparticle paste onto a glass slide followed by low temperature sintering. The electrical resistivity of the copper film using glycolic acid as the capping agent was 25.5 ± 8.0 and 34.8 ± 9.0 μΩ·cm after annealing at 150 and 200 °C for 60 min under nitrogen, respectively. When lactic acid was used as the capping agent, the electrical resistivity of the copper films was 21.0 ± 7.0 and 9.1 ± 2.0 μΩ·cm after annealing at 150 and 200 °C for 60 min under nitrogen, respectively, with the latter being about five times greater than the resistivity of bulk copper (1.7 μΩ·cm).

Facile synthesis and electrical performance of silica-coated copper powder for copper electronic pastes on low temperature co-fired ceramic

Submicron Cu@glass core-shell powders for the preparation of conductive thick films on ceramic substrates

Thermal Sintering Matchability Between Low‐Temperature Cofired Ceramic Substrate and Silver Pastes and the Effect of CuO on Silver Diffusion Inhibition

Preparation and properties of antioxidative BaO–B2O3–SiO2 glass-coated Cu powder for copper conductive film on LTCC substrate

Thermal Sintering Matchability between LTCC Substrate and Silver Pastes and the Effect of CuO on Silver Diffusion Inhibition

Surfactant-stabilized copper paticles for low-temperature sintering: Paste preparation using a milling with small zirconia beads: Effect of pre-treatment with the disperse medium

Preparation and sintering properties in air of silver-coated copper powders and pastes

Sintering Densification of Cu/Al2O3p Nano-Composite Powders by Electroless Copper Plating

Electroless Co-P Alloy Plating of Superfine Si3N4 Powders

Copper film prepared from copper fine particle paste by laser sintering at room temperature: Influences of sintering atmosphere on the morphology and resistivity

The microstructure and properties of copper coating fabricated by high velocity arc spraying

Study on Low-Temperature Conductive Silver Pastes Containing Bi-Based Glass for MgTiO3 Electronic Power Devices

Effect of silica addition on microstructure, sintering behavior, and dielectric properties of borosilicate glass/alumina composites for LTCC application

Sintering of SiC enhanced copper paste for high power applications

Photonic sintering of copper for rapid processing of thick film conducting circuits on FTO coated glass

Copper nanoparticles: aqueous phase synthesis and conductive films fabrication at low sintering temperature.

Low-temperature sintering of Cu@Ag microparticles in air for recyclable printed electronics

Study on the Resistivity and Porosity of Nano Copper Powder Under Low-Temperature Sintering without Pressure

A mild aqueous synthesis of ligand-free copper nanoparticles for low temperature sintering nanopastes with nickel salt assistance

Rapid Low Temperature Sintering in Air of Copper Submicron Particles with Synergistic Surface-Activation and Anti-Oxidative Protection

Rapid and Low Temperature Sintering Bonding Using Cu Nanoparticle Film for Power Electronic Packaging