Abstract:Pure copper is widely used in motor windings, heat exchangers and aerospace engines because of its high electrical and thermal conductivity. High-strength laser powder bed fusion (HS-LPBF) not only allows rapid production of components with complex geometry and high spatial resolution, but also offers various advantages such as small focal spot diameter, fine powder, and small layer thickness, providing advantages for forming complex structural parts in fields such as engines and heat exchangers. A single factor single layer experiment was performed by varying the hatch spacing (H), and the range of hatch spacing was determined according to the overlap rate. The degree of influence of process parameters on the relative density of pure copper specimens was analyzed using an orthogonal experiment, and a comparative study of the phase composition, microstructure and mechanical properties of pure copper specimens was carried out by varying the laser power. The characteristics of pure copper formed by HS-LPBF were analyzed. In addition, the effect of heat treatment on the microstructure and mechanical properties of pure copper specimens was investigated, and the fracture morphology of the specimens was observed comparatively. The results show that the HS-LPBF technique can effectively increase the energy density and improve the specific surface area of the powder and the laser absorptivity due to its small focal spot diameter, fine powder and layer thickness, thus reducing the minimum energy required to melt pure copper powder. The optimum process parameters were obtained by orthogonal experiment with a relative density of 98.1 % of the specimen. The highest hardness, ultimate tensile strength and elongation were obtained at a laser power of 260 W with 84 HV, 320 MPa and 17.8 %, respectively. This ultimate tensile strength is 18 % higher than the highest ultimate tensile strength that has been reported so far. In addition, the average grain size of the optimal specimens was 3.6 μm. Mechanical properties such as hardness, tensile strength and elongation of pure copper parts can be significantly improved by precisely controlling the process parameters, in particular laser power and hatch spacing.

Copper film prepared from copper fine particle paste by laser sintering at room temperature: Influences of sintering atmosphere on the morphology and resistivity

Study on the Technology and Properties of Green Laser Sintering Nano-Copper Paste Ink

Facile synthesis and electrical performance of silica-coated copper powder for copper electronic pastes on low temperature co-fired ceramic

Rapid Low Temperature Sintering in Air of Copper Submicron Particles with Synergistic Surface-Activation and Anti-Oxidative Protection

Copper nanoparticles: aqueous phase synthesis and conductive films fabrication at low sintering temperature.

Photonic sintering of copper for rapid processing of thick film conducting circuits on FTO coated glass

Study on the Resistivity and Porosity of Nano Copper Powder Under Low-Temperature Sintering without Pressure

Copper circuits fabricated on flexible polymer substrates by a high repetition rate femtosecond laser-induced selective local reduction of copper oxide nanoparticles.

Thermal Analysis of Cu-Organic Composite Nanoparticles and Fabrication of Highly Conductive Copper Films

Anisotropic material properties of pure copper with fine-grained microstructure fabricated by laser powder bed fusion process

Microstructures and mechanical properties of pure copper manufactured by high-strength laser powder bed fusion

Fabrication and investigation of a new copper-doped screen-printable carbon paste's conductive mechanism by AFM

Mixed Ink of Copper Nanoparticles and Copper Formate Complex with Low Sintering Temperatures

Preparation and sintering properties in air of silver-coated copper powders and pastes

The effects of complex agent and sintering temperature on conductive copper complex paste

Low-temperature sintering of Cu@Ag microparticles in air for recyclable printed electronics

Electroless Deposition of Confined Copper Layers Based on Selective Activation by Pulsed Laser Irradiation

In-air sintering of copper nanoparticle paste with pressure-assistance for die attachment in high power electronics

Surfactant-stabilized copper paticles for low-temperature sintering: Paste preparation using a milling with small zirconia beads: Effect of pre-treatment with the disperse medium

High-precision laser powder bed fusion processing of pure copper

Ambient Aqueous-Phase Synthesis of Copper Nanoparticles and Nanopastes with Low-Temperature Sintering and Ultra-High Bonding Abilities