Abstract:Light alloys are being increasingly investigated as alternatives to ferrous-based engineering components, based on weight considerations. However, in-service applications of such light alloy components often require a surface modification step to enhance their wear and corrosion responses for improved functionality. Thermally sprayed cermet coatings offer an enhanced resistance to wear and corrosion. This work investigates WC-CoCr coatings deposited using two different feedstocks comprising fine and coarse powder size distributions on aluminum alloy and steel substrates using high-velocity air-fuel (HVAF) and high-velocity oxy-fuel (HVOF) spray techniques. The WC-CoCr coatings were HVAF sprayed at various parameters to investigate the relationship between the processing conditions, microstructure, and performance. Microindentation, dry sliding wear, dry sand abrasion, cavitation erosion, and corrosion tests were conducted to assess the performance of the coatings. Despite the qualitative similarities in the microstructures of the coatings, the measured microindentation hardness values were observed to vary, and coatings deposited with higher particle impact velocities showed the highest microhardness between 1400 and 1600 HV0.3. For the three categories of wear investigated, the HVAF coatings showed better resistance than the HVOF coating investigated in this study. The estimated average specific wear rate (SWR) due to sliding wear of the HVOF coating was ~ 16.7 ± 4.0 × 10 −8 mm 3 /Nm compared to that of the most resistant HVAF coating, which exhibited a SWR of ~ 1.7 ± 0.6 × 10 −8 mm 3 /Nm. The cumulative mass loss rate due to the abrasive wear on the HVOF coating reached ~ 1.11 mg/min compared to ~ 0.76 mg/min of the most abrasion-resistant HVAF coating. All coatings showed similar corrosion resistances under the investigated conditions. The combination of wear and corrosion performance of the respective coatings could provide insight into the coating selection for intended applications.

Effect of prolonged immersion on corrosion and cavitation resistance of HVOF-sprayed WC-NiCr and WC-Hastelloy cermet coatings

Microstructure and Corrosion Behaviour of WC-Co Coating Fabricated by Plasma Arc Welding

Effect of Marine Bacillus Subtilis on Cavitation Erosion Resistance of HVOF-Sprayed WC-10Co-4Cr Coating in Artificial Seawater

Wear and Corrosion of HVAF and HVOF-Sprayed WC-CoCr Coatings on Aluminum Alloy

Corrosion–Cavitation Erosion Improvement of Marine Steel by High-Velocity Oxy-fuel-Sprayed Vanadium Carbide Coatings and Polytetrafluorethylene Topcoat

Resistance of HVOF-Sprayed Cr3C2-25NiCr and WC-10CO-4Cr coatings to cavitation and erosion by mud jetting

Hydro-abrasive Erosion and Cavitation-Silt Erosion Characteristics of HVOF Sprayed WC-Ni Cermet Coatings under Different Flow Velocities and Sand Concentrations

Cavitation-silt erosion behavior and mechanism in simulated sea water slurries of cermet coatings manufactured by HVOF spraying

Effect of 3.5 % NaCl solution with different Na 2 S concentrations on ultrasonic cavitation erosion behaviors of HVOF sprayed WC-Ni coatings

Experimental Investigations on Erosion-Corrosion Characteristics of HVOF-Sprayed WC-10% Ni Coatings Deposited on Aluminum Alloy

Effects Of Wc Crystal Characteristics On Microstructure And Mechanical Property Of Hvof-Sprayed Wc-Cocr Coatings

CAVITATION EROSION BEHAVIOR OF WC–Co COATINGS ON TURBINE STEEL DEPOSITED BY COLD SPRAY

Cavitation erosion resistance in NaCl medium of HVOF sprayed WC-based cermet coatings at various flow velocities: A comparative study on the effect of Ni and CoCr binder phases

Evaluation of cavitation/corrosion synergy of the Cr3C2-25NiCr coating deposited by HVOF process

Enhanced slurry and cavitation erosion resistance of deep cryogenically treated thermal spray coatings for hydroturbine applications

Influences of Sand Concentration and Flow Velocity on Hydro-Abrasive Erosion Behaviors of HVOF Sprayed Cr3C2–NiCr and WC–Cr3C2–Ni Coatings

Comparison on Long-Term Corrosion Performance of WC-CoCr and Al2O3-TiO2 Ceramic Coatings in Sulphide-Containing 3.5 Wt% NaCl Solution

Effects of microstructure and mechanical properties on cavitation erosion resistance of NiCrWMoCuCBFe coatings

A comparative assessment on the characteristics of HVOF sprayed cermet coatings

Investigation on Microstructure, Mechanical and Wear Properties of HVOF Sprayed Composite Coatings (WC-Co + CR) On Ductile Cast Iron

Cavitation Erosion Behavior of Co-28Mo-8Cr-2Si Coating in Deionized Water and Artificial Seawater