Abstract:Highly porous and hydrophobic silica aerogel is fabricated using fly ash and trona ore as the starting materials and the cost-effective ambient pressure drying technique. The optimal calcination parameters are determined as temperature of 850°C, holding time of 2h, and the trona ore/fly ash mass ratio of 1.4. The CO2 release mechanism during calcination is proposed and has been verified by the Thermogravimetric and Differential Scanning Calorimetry analysis (TG/DSC) and X-ray fluorescence (XRF) technique. The hydrogel is derived from reacting the calcination mixture with sulphuric acid solution, followed by filtration. The impurities can be effectively removed through water washing and solvent exchange processes. No ion exchange resin is used in this preparation method, and thus it is a safe, inexpensive and much more straightforward process. In order to minimize drying shrinkage, the hydrogel is first transformed into an alcogel by soaking in ethanol, after which the alcogel is surface modified with the hexane/ethanol/trimethylchlorosilane (hexane/ethanol/TMCS) mixture solution. It has been observed that the specific surface area, BJH desorption pore volume, and BJH desorption average pore diameter all first increase and then decrease so that reach to the maximum values once the heat treatment temperature approaches 500°C due to the oxidation of CH3 groups on the silica skeleton surface. The final product presents special characteristics including: (1) high thermal stability for maintaining hydrophobicity up to 476°C, (2) contact angle of the as-dried silica aerogel as high as 151°, (3) silica particle size of ca. 3–6nm, agreeing well with the model as reported, (4) and the 500°C heat treated sample possessing a large specific surface area of 856.2m2/g, a large pore volume of 2.92cm3/g, and a BJH desorption average pore diameter of 17.1nm. The proposed inexpensive approach produces silica aerogel with superior properties and is a scalable-manufacturing method for large-scale industrial production.

Production of low-density sodium silicate-based hydrophobic silica aerogel beads by a novel fast gelation process and ambient pressure drying process

Synthesis and characterization of micrometer-sized silica aerogel nanoporous beads

Synthesis of sodium silicate-based hydrophilic silica aerogel beads with superior properties: Effect of heat-treatment

Synthesis and characterization of silica aerogels by a novel fast ambient pressure drying process

Preparation of high-strength silica aerogels by two-step surface modification via ambient pressure drying

Synthesis and characterization of low density and hydrophobic silica aerogels dried at ambient pressure using sodium silicate precursor

Preparation of Methyltrimethoxysilane Derived Silica Aerogel Films via Ambient Pressure Drying

Superhydrophobic silica aerogel powders with simultaneous surface modification, solvent exchange and sodium ion removal from hydrogels

Low thermalconductive, transparent and hydrophobic ambient pressure dried silica aerogels with various preparation conditions using sodium silicate solutions

Rapid synthesis of ambient pressure dried tetraethoxysilane based silica aerogels

Convenient and rapid preparation of aerogels dried at ambient pressure

Synthesis of hydrophilic and hydrophobic xerogels with superior properties using sodium silicate

Enhancing Mesopore Volume and Thermal Insulation of Silica Aerogel via Ambient Pressure Drying-Assisted Foaming Method

Rapid synthesis of sodium silicate based hydrophobic silica aerogel granules with large surface area

A novel low-cost method of silica aerogel fabrication using fly ash and trona ore with ambient pressure drying technique

Synthesis of Hydrophobic Silica Aerogels via Ambient Pressure Drying

Preparation and Characterization of Hydrophobic Silica Aerogel by Ambient Pressure Drying Method

Effect of different trimethyl silylating agents on the hydrophobic and physical properties of silica aerogels

Silica aerogels formed from soluble silicates and methyl trimethoxysilane (MTMS) using CO2 gas as a gelation agent

Effects of Surfactants on the Synthesis of Silica Aerogels Prepared by Ambient Pressure Drying

Synthesis of high specific surface area silica aerogel from rice husk ash via ambient pressure drying