Abstract:Objective: The objective of the present study was to investigate the feasibility and reliability of sintering alumina and zirconia-based all-ceramic materials through a recently introduced microwave heating technique. The variation of crystal phases, the growth of grain sizes and microstructural features of these materials were evaluated after sintering. Methods: Four different groups of powder (l00%Al2O3, 60%Al2O3+40%ZrO2, 40% Al2O3+60%ZrO2, 100% ZrO2) were respectively press-compacted to fabricate green disk samples, 5 specimen of each group were prepared. All the samples were surrounded by refractory materials for heat containment and processed at 1 600 degrees C in a domestic microwave oven (850 W, 2 450 MHz), 1 600 degrees C/5 min for heating rate, 10 min for holding time. After sintering, the phase composition and average grain size of these ceramics were examined using X-ray diffraction (XRD). Their microstructure characteristics were studied by scanning electron microscopy (SEM). Results: All the specimens were successfully sintered with the application of microwave heating system in combination with a suitable thermal insulator. No phase change was found in alumina while monoclinic-zirconia was found to be transformed to tetragonal-zirconia. A little grain size growth of Al2O3 and ZrO2 has been observed with Al2O3 24.1 nm/before and 51.8 nm/after; ZrO2 25.3 nm/before and 29.7 nm/after. The SEM photos indicated that the microwave-sintered Al2O3-ZrO2 ceramics had a uniform crystal distribution and their crystal sizes could be maintained within the range of nanometers. Conclusion: It is expected that in the near future microwave heating system could be a promising substitute for conventional processing methods due to its unparalled advantages, including more rapid heating rate, shortened sintering time, superfine grain size, improved microstructure and much less expensive equipment.

High‐performance Al 2 O 3 ceramics prepared by DCC‐HVCI via microwave heating

Influence of CaO content by mass in sintering aid and sintering temperature on the properties of Al2O3-based microwave ceramic materials

[Microwave sintering of nanometer powder of alumina and zirconia-based dental ceramics]

Effect of UV irradiation on the densification behavior, microstructure, and microwave dielectric properties of low temperature sintering Al2O3 ceramics

Low -temperature sintering of Al2O3 microwave dielectric ceramic doped with CuO-TiO2 gel

Properties of Alumina Coagulated Bodies Prepared by Direct Coagulation Casting Via High Valence Counter Ions (DCC‐HVCI)

Reliable High Strength Alumina Fabricated by DCC-HVCI Using Submicron Calcium Citrate Complex

Microstructure and phase transformation behavior of Al2O3–ZrO2 under microwave sintering

Microwave Sintering of Ce-Y-Zta Composites

Low-temperature sintering of Al2O3 ceramics doped with 4CuO-TiO2-2Nb2O5 composite oxide sintering aid

Fabrication of high-temperature resistant Y–Al–Si–O composite ceramics with enhanced mechanical/thermal/dielectric properties

Enhanced microwave dielectric properties of Al2O3 ceramics via a cold sintering assisted two-step sintering route

Microstructure refinement-homogenization and flexural strength improvement of Al2O3 ceramics fabricated by DLP-stereolithography integrated with chemical precipitation coating process

Reducing Water Absorption and Improving Flexural Strength of Aluminosilicate Ceramics by MnO2 Doping

Effect of MnCO3 on Eliminating Al2TiO5 Phase and Dielectric Properties of 0.90Al2O3–0.10TiO2 Composite Ceramics

The Improved Thermal Conductivity of a Potting Material for High-Power Fast Warm-Up Cathodes

Preparation of CuO-TiO2 Composite Nanopowder and In-Situ Doping in Al2O3 Microwave Dielectric Ceramics

Effect of Al(OH) 3 on the Properties of Silica-based Ceramic Cores Prepared by Laser Powder Bed Fusion Combined with Vacuum Infiltration

Direct coagulation casting of alumina slurry and its technics

Lightweight porous Al2O3‐based ceramics with highly controllable performance via binder jetting

Low sintering shrinkage and high strength of porous mullite–zirconia ceramics: Effect of AlF3 and ZrSi2 contents