Abstract:Cracking is one of the main causes for deterioration of concrete structures. Self-healing concrete with 3D-printed vascular networks has excellent potential for autonomous self-healing. This approach is scarcely investigated: no studies have been devoted to the influence of printing parameters on the properties of vascular based self-healing concrete. In this work, three-dimensional vascular structures with complex geometry were designed and printed with 4 different sets of printing parameters. First, the influence of the four, nominally identical, vascular networks on the initial flexural strength of self-healing concretes was experimentally investigated. In parallel, numerical modeling with a concrete damaged plasticity model (CDPM) in Abaqus software is used to simulate the influence of vascular networks on the mechanical properties of the self-healing composite. After the 4-point bending tests, epoxy resin is injected into the vascular networks as the healing agent to seal the cracks. Then, flexural strength regain and watertightness recovery were also measured. Based on the obtained results, we found that vascular based self-healing concretes have lower initial flexural strengths than the reference sample, as expected. The magnitude of the strength drop is shown to depend strongly on the printing parameters: the specimens with horizontally-printed vascular networks have higher flexural strength than the vertically-printed counterparts. Furthermore, vascular networks with a smaller printing layer-height have less influence on the initial flexural strength of vascular-based self-healing concrete compared to those with the larger printing layer-height. In terms of watertightness recovery, all tested vascular based self-healing samples showed a full (100%) recovery, which means that the printing direction and printing layer-height do not have an obvious effect on the watertightness recovery in this study. Numerical simulations of the mechanical performance of the composites with the CDPM show good agreement with the experiments, although printing quality of the vascular network influences the simulation accuracy. These simulations show great potential of using numerical simulations to design vascular based self-healing concrete in order to minimize a drop in mechanical properties, without compromising the healing efficiency. Overall, the designed 3D-printed vascular self-healing concretes show remarkable strength regain and watertightness recovery and provide a good basis for further research.

Enhancing Mechanical Properties of Concrete with 3D Printed Vascular Networks via Carbonation strengthening

Investigation of the Internal Structure of Hardened 3D-Printed Concrete by X-CT Scanning and Its Influence on the Mechanical Performance.

Mechanical properties and healing efficiency of 3D-printed ABS vascular based self-healing cementitious composite: Experiments and modelling

Self-healing cementitious composites with a hollow vascular network created using 3D-printed sacrificial templates

Direct ink writing of vascularized self-healing cementitious composites

PVA Fibre Reinforced High-Strength Cementitious Composite for 3D Printing: Mechanical Properties and Durability

Research on Mechanical Properties of a 3D Concrete Printing Component-Optimized Path by Multimodal Analysis

Expansive cementitious materials to improve micro-cable reinforcement bond in 3D concrete printing

3D-printing of architected calcium silicate binders with enhanced and in-situ carbonation

Rheological behaviors and structure build-up of 3D printed polypropylene and polyvinyl alcohol fiber-reinforced calcium sulphoaluminate cement composites

Influence of steel fiber on the water absorption of 3D printed concrete

Use of Carbonation Curing to Improve Mechanical Strength and Durability of Pervious Concrete

A study of the effects of MWCNTs on the fresh and hardened state properties of 3D printable concrete

A novel method for improving the printability of cement-based materials: Controlling the releasing of capsules containing chemical admixtures

Mechanical behaviors of 3D printed lightweight concrete structure with hollow section

Influence of pore defects on the hardened properties of 3D printed concrete with coarse aggregate

Improving printability of limestone-calcined clay-based cementitious materials by using viscosity-modifying admixture

Modification effect of nanosilica and polypropylene fiber for extrusion-based 3D printing concrete: Printability and mechanical anisotropy

Experimental Research on Mechanical Performance of Hybrid Fiber Reinforced Cementitious Composites with Polyvinyl Alcohol Short Fiber and Carbon Textile

Shrinkage and mechanical properties optimization of spray-based 3D printed concrete by PVA fiber

Mechanical and macrostructural properties of 3D printed concrete dosed with steel fibers under different loading direction