Abstract:In recent years, the use of CFRP with titanium and/or aluminum to form materials for stacking has gained popularity for aircraft construction. In practice, single-shot drilling is used to create perfectly aligned holes for the composite-metal stack. Usually, standard twist drills, which are commonly available from tool suppliers, are used for practical reasons. However, existing twist drill bits exhibit rapid wear upon the drilling of composite-metal stack layers in single shot, due to the widely contrasting properties of the composite-metal stack, which causes poor surface quality. The stringent quality requirements for aircraft component manufacturing demands frequent drill bit replacement and thus incurs additional costs, a concern still unresolved for aircraft component manufacturers. Owing to highly contrasting properties of a composite-metal stack, it is obvious that standard twist drill cannot fulfil the rigorous drilling requirements, as it is pushed to the limit for the fabrication of high-quality, defect-free holes. In this work, customised twist drills of a tungsten carbide (WC) material with different geometric features were specially fabricated and tested. Twenty drill bits with customised geometries of varying chisel edge angle (30-45°), primary clearance angle (6-8°), and point angle (130-140°) were fabricated. The stacked-up materials used in this study was CFRP and aluminum alloy 7075-T6 (Al7075-T6) with a total thickness of 3.587 mm. This study aims to investigate the effect of twist drill geometry on hole quality using drilling thrust force signature as indicator. All drilling experiments were performed at spindle speed of 2600 rev/min and feed rate of 0.05 mm/rev. Design of experiments utilising response surface methodology (RSM) method was used to construct the experimental array. Analysis of variance (ANOVA) was used to study the effect of parameters and their significance to the thrust force and thus the hole quality. The study shows that the most significant parameter affecting the drilling thrust force and hole surface roughness is primary clearance angle, followed by chisel edge angle. Correlation models of CFRP thrust force (Y1), Al7075-T6 thrust force (Y2), CFRP hole surface roughness (Y3), Al7075-T6 hole surface roughness (Y4) as a function of the tool geometry were established. The results indicated that the proposed correlation models could be used to predict the performance indicators within the limit of factors investigated. The optimum twist drill geometry was established at 45° of chisel edge angle, 7° of primary clearance angle, and 130° of point angle for the drilling of CFRP/Al7075-T6 stack material in a single-shot process. The error between the predicted and actual experiment values was between 6.64% and 8.17% for the optimum drill geometry. The results from this work contribute new knowledge to drilling thrust force signature and hole quality in the single-shot drilling of composite-metal stacks and, specifically, could be used as a practical guideline for the single-shot drilling of CFRP/Al7075-T6 stack for aircraft manufacturing.

A comparative study of hole integrity performance in composite‐metal stacks using coated and uncoated tungsten carbide drill bitsVergleichende Studie zur Lochintegritätsleistung in Verbundmetallstapeln unter Verwendung von beschichteten und unbeschichteten Wolframkarbid‐Bohrern

Hole Diameter Variation and Roundness in Dry Orbital Drilling of Cfrp/Ti Stacks

A New Strategy of Carbon Fiber Reinforced Plastic Drilling Evaluation Using Thermal Measurement

A comparative study of hole-making performance by coated and uncoated WC/Co cutters in helical milling of Ti/CFRP stacks

Hole quality and tool wear when dry drilling of a new developed metal/composite co-cured material

A study on the machinability of advanced arc PVD AlCrN-coated tungsten carbide tools in drilling of CFRP/titanium alloy stacks

Influence of HSS drill coatings on surface finish and cylindricity of AA6061 / C / ZrO2 composite in CNC drilling operations under dry conditions

Multi-Objective Optimization in Single-Shot Drilling of CFRP/Al Stacks Using Customized Twist Drill

Performance analysis of uncoated and coated (TiN-, TiAlN-) carbide drills in drilling graphene-reinforced GF/epoxy nanocomposites: Analytical and experimental study

Study on the Orthogonal Cutting Process of Al7050T7451 with Uncoated and Coated Tools

Effectiveness of lubricating coatings in dry drilling of aluminium alloys

Study on the working performance of CrAlCN coated and uncoated carbide twist drill

High-speed drilling mechanism study of unidirectional CoCrFeNiAl fiber-reinforced aluminum matrix composites

Evaluation of Cutting-Tool Coating on the Surface Roughness and Hole Dimensional Tolerances during Drilling of Al6061-T651 Alloy

Optimization for drilling process of metal-composite aeronautical structures

Lubricant Coatings for Mobile Dry Drilling of Stacked Aluminium Alloys

Exploring novel PVD coated wiper inserts' chip breaker designs and feed rates on tool wear and in-depth hole integrity of Ti-6Al-4V alloy when drilling in a dry environment

Hybrid Composite-Metal Stack Drilling with Different Minimum Quantity Lubrication Levels

The performance of advanced cutting tools used for dry machining of aluminium

Study on the surface integrity of micro-holes in high volume fraction SiCp/Al using ultrasonic vibration drilling

Mechanical and cutting performance of cemented carbide tools with Cr/x/DLC composite coatings