Abstract:The new developed metal/composite co-cured material composed of carbon fiber–reinforced plastic and Al phases has been increasingly applied for manufacturing of attitude control flywheel in aerospace industry. However, drilling of co-cured material is still a challenging task to produce holes with high quality and low cost in the assembly chain and dynamic balance debugging of attitude control flywheel. In other words, the relevant mechanisms and experimental findings involved in the drilling process of carbon fiber–reinforced plastic/Al co-cured material is not clearly defined, which impedes the progress of attitude control flywheel production. To this end, this article specially addresses the experimental studies on the drilling process of carbon fiber–reinforced plastic/Al co-cured material with standard TiAlN-coated cemented carbide twist drill. The significance of this work aims to reveal the regardful cutting responses of the hole characteristics and tool wear modes during the practical drilling process of co-cured material. A full factorial experiment including three levels of feed rate and four levels of cutting speed was performed. The hole diameter shows different values in different positions while it indicates consistent pattern regardless of the cutting variables: the largest in the Al phase, followed by the upper and lower carbon fiber–reinforced plastic phases, respectively. Grooves and matrix degradation are the major machining defects for carbon fiber–reinforced plastic layers, while a great chip debris adhered to the machined surface is the case for Al layer. Subsequent wear analysis showed that abrasion was mainly maintained at the vicinity of major/minor cutting edges and drill edge corner, followed by chip adhesion on the chisel edge region. Carbide substrate of drill flank face is exposed, and thereafter cavities are formed under the strong mechanical abrasion. These results could provide several implications for industrial manufacturers during the attitude control flywheel production.

Hole Diameter Variation and Roundness in Dry Orbital Drilling of Cfrp/Ti Stacks

Processing research on orbital drilling of CFRP/Ti-6Al-4V stacks

Modeling of Non-Linear Cutting Forces for Dry Orbital Drilling Process Based on Undeformed Chip Geometry

Analysis of the Chip-Splitting Performance of a Dedicated Cutting Tool in Dry Orbital Drilling Process

Experimental Study on Drilling Mechanisms and Strategies of Hybrid CFRP/Ti Stacks

Influence of Metal Chips on Drilling Quality of Carbon Fiber Reinforced Plastic and Titanium Stacks

Study on Tool Deflection Compensation Method Based on Cutting Force Observer for Orbital Drilling of CFRP/Ti Stacks

Investigation of CFRP damages induced by the interface high temperature and mixed tool wear mechanism in drilling of thin-walled CFRP /Ti stacks

A comparative study of hole-making performance by coated and uncoated WC/Co cutters in helical milling of Ti/CFRP stacks

Experimental study on step drill geometry and pecking drilling with variable parameters processing method as drilling of CFRP and Ti stacks

Investigation of Drilling CFRP-TC4 Stacks

On the Analysis of Temperatures, Surface Morphologies and Tool Wear in Drilling CFRP/Ti6Al4V Stacks under Different Cutting Sequence Strategies

Investigation on the cutting responses of CFRP/Ti stacks: With special emphasis on the effects of drilling sequences

Experimental Study on Mechanical Drilling of Carbon/epoxy Composite-Ti6al4v Stacks

Influence of main cutting edge structure on hole defects in CFRP/titanium alloy stacks drilling

Effect of Drilling Parameters and Tool Geometry on Drilling Performance in Drilling Carbon Fiber–reinforced Plastic/titanium Alloy Stacks

On the Interpretation of Drilling CFRP/Ti6Al4V Stacks Using the Orthogonal Cutting Method: Chip Removal Mode and Subsurface Damage Formation

Drilling Temperature and Hole Quality in Drilling of CFRP/aluminum Stacks Using Diamond Coated Drill

Hole quality and tool wear when dry drilling of a new developed metal/composite co-cured material

Experimental Study on Longitudinal-Torsional Ultrasonic Vibration Drilling of Carbon Fiber–reinforced Plastics/titanium Alloy Stacks

Numerical Study of Step Drill Structure on Machining Damage in Drilling of CFRP/Ti Stacks