Abstract:Wear due to sliding is an inevitable problem in many engineering applications. Protective surface coating is usually used to mitigate this problem. The development in this field is continuous and consistent. There are many types of coatings according to their compositions and the deposition methods. One of the coatings with the most promising properties, such as the hardness, is the Diamond-Like Carbon (DLC) coating. The tribological properties of this coating generated by Plasma-Assisted Chemical Vapor Deposition (PACVD) and applied on bearing steel 52100 ASTM are not available. In this study, the wear resistance of the DLC coating applied to bearing steel 52100 ASTM, was evaluated. The coating method employed was PACVD, which is regarded as one of the most distinctive coating techniques due to the unique tribological properties imparted to the coating. The pin-on-disc tribometer was used to examine the coefficient of friction and mass losses for samples of (steel disc against steel ball) and (DLC coated disc against DLC coated ball) under constant sliding velocity and constant sliding distance with four different loads (2, 5, 10 and 20 N) that results in maximum contact pressure below and higher than the maximum shear stress of the bearing steel. The wear coefficient was calculated using Archard's equation based on the experimental results. It was found that the DLC coating may result in significant reduction, reaching 93.5%, in weight loss and 83% in COF at low contact pressure (less than the maximum shear stress). However, at high contact pressure (equals to or higher than the maximum shear stress) the weight loss and the COF for the DLC coating are higher than those of the bearing steel. This behavior indicates that the DLC coated pair may not be suitable at high loads. The wear coefficient is calculated for each testing condition and it is found to be affected by the applied load. The average wear coefficient for the DLC coating is provided which can be used with the Archared wear model to predict the wear rate within the range of the parameters used in this study.

Effectiveness of lubricating coatings in dry drilling of aluminium alloys

Lubricant Coatings for Mobile Dry Drilling of Stacked Aluminium Alloys

Establishing cutting conditions for dry drilling of aluminium alloy stack materials

Evaluation of the drilling process in 6061-T6 Al-Mg-Si alloys using AISI M-35 diamond-like carbon coated high-speed steel drill

Tribological and dry drilling performance of WS2/Cr-AlCrN coatings

A study on the machinability of advanced arc PVD AlCrN-coated tungsten carbide tools in drilling of CFRP/titanium alloy stacks

Evaluation of Cutting-Tool Coating on the Surface Roughness and Hole Dimensional Tolerances during Drilling of Al6061-T651 Alloy

Synthesis and characterization of diamond-like carbon coatings for drill bits using plasma-enhanced chemical vapor deposition

The performance of advanced cutting tools used for dry machining of aluminium

Study on the Orthogonal Cutting Process of Al7050T7451 with Uncoated and Coated Tools

Influence of HSS drill coatings on surface finish and cylindricity of AA6061 / C / ZrO2 composite in CNC drilling operations under dry conditions

A comparative study of hole integrity performance in composite‐metal stacks using coated and uncoated tungsten carbide drill bitsVergleichende Studie zur Lochintegritätsleistung in Verbundmetallstapeln unter Verwendung von beschichteten und unbeschichteten Wolframkarbid‐Bohrern

A Comparative Experimental Study on Machining Performance of Aluminium against Advanced Diamond Coated Cutting Tool Inserts

Effects of DLC/TiAlN-coated die on friction and wear in sheet-metal forming under dry and oil-lubricated conditions: Experimental and numerical studies

Study of Diamond-Like Carbon coating application on carbide substrate for cutting tools used in the drilling process of an Al–Si alloy at high cutting speeds

The effect of diamond like carbon coating on the wear resistance at dry sliding conditions

Evaluation of the performance of DLC Coatings (ta-C) of WC-Co tools while machining Al7075 alloy

Drilling-induced damage suppression on CFRP/Ti-6Al-4V stacks using textured drills

Experimental investigation on drilling machinability and hole quality of CFRP/Ti6Al4V stacks under different cooling conditions

Hole quality and tool wear when dry drilling of a new developed metal/composite co-cured material

Wear behaviors of PCD and diamond-coated tools during low-frequency vibration-assisted drilling CFRP/Ti stacks