Abstract:In this study, continuous microcrystalline diamond layer with grain size of 0.8–2 µm, nanocrystalline diamond layer with grain size less than 100 nm, diamond-like carbon layer with no apparent grains and TiAlN layer with small particles on the top surface are successfully deposited on cemented tungsten carbide-cobalt (WC-Co) samples and microdrills. Diamond peak of microcrystalline diamond film is quite definite in the Raman spectrum, while that of nanocrystalline diamond and diamond-like carbon coating is not so apparent. The roughness of microcrystalline diamond, nanocrystalline diamond, diamond-like carbon coating and TiAlN coatings is about 215.83, 144.4, 23.63 and 168.17 nm, respectively. Nanocrystalline diamond film exhibits lowest adhesive strength between substrate, while diamond-like carbon exhibits highest adhesive strength between substrate. Tribotests show stable friction coefficients of microcrystalline diamond, nanocrystalline diamond, diamond-like carbon and TiAlN coatings as about 0.28, 0.08, 0.08 and 0.4, respectively, while their wear rates against Si3N4 balls are 4.9E−7, 7.0E−7, 7.7E−7 and 2.9E−6 mm3 N−1 m−1, respectively. Microdrilling experiments show that the tool life of microcrystalline diamond–coated microdrill is as about 1.5, 2, 6 and 9 times more than that of nanocrystalline diamond-, diamond-like carbon-, TiAlN-coated and uncoated microdrills, respectively. The main wear types of these microdrills are flank wear, chipping and coating delamination. The results show that the microcrystalline diamond film is more suitable to be deposited on microdrills than the other three coatings to enhance cutting performance of microdrills in dry machining of graphite.

Study on the working performance of CrAlCN coated and uncoated carbide twist drill

Application of Magnetron Sputter Ion Plated CrAlTiN Composite Coating in Improving Wear Resistance of Milling Cutter

Tribological and dry drilling performance of WS2/Cr-AlCrN coatings

Experimental Study on the Dry Drilling Nickel-Based Superalloy of CrAlYN Coated Carbide Bit

DEVELOPMENT AND EXPERIMENT OF NEW AlTiN COATED DRILLS FOR HIGH EFFICIENCY DRY DRILLING OF 40Cr

Study on the Orthogonal Cutting Process of Al7050T7451 with Uncoated and Coated Tools

Mechanical and cutting performance of cemented carbide tools with Cr/x/DLC composite coatings

A study on the machinability of advanced arc PVD AlCrN-coated tungsten carbide tools in drilling of CFRP/titanium alloy stacks

Study on the surface performance strengthening of AlCrN coated cemented carbide by micro-texture laser preparation process

Microstructure, mechanical properties and high-speed dry-cutting performance of AlCrSiCN composite coatings

Preparation and Drilling Characteristics of Diamond Coated Cemented Carbide Step Cutting Tool

Microstructure and Properties of the AlCrSi(O)N Tool Coatings by Arc Ion Plating

The Wear Mechanism of New Type of Drill Coated with TiCN

Study on the Wear Mechanism and Tool Life of Coated Gun Drill

Research on Wear Mechanism of Coated HSS Drills during Machining Stainless Steel

Effect of Deposition Parameters on Micromechanical Properties and Machining Performance of CrN Coating for Wet Finish Turning of Ti6Al4V Alloy

Preparation and Performance of a Cr/CrN/TiAlCN Composite Coating on a GCr15 Bearing Steel Surface

Influence of different wet-blasting pressure on the surface integrity and tool cutting performance of hybrid CVD-TiN/TiCN/α-Al2O3/TiN coated tools

Influence of Cr on the Surface Properties of the Micro-Textured WC+Co Alloy Coating

Influence of HSS drill coatings on surface finish and cylindricity of AA6061 / C / ZrO2 composite in CNC drilling operations under dry conditions

Comparison of Chemical Vapor Deposition Diamond-, Diamond-Like Carbon- and TiAlN-coated Microdrills in Graphite Machining