Abstract:This paper is focused on the rolling finite element simulation and experimental study of 20CrNiMo/Incoloy 825 composite materials. Firstly, single-pass rolling finite element simulations of the composite materials were conducted. The effects of rolling pass reduction and rolling speed on the warpage, interface strain difference, and stress of the 20CrNiMo/Incoloy 825 composite materials were evaluated, highlighting an ideal first-pass reduction of 30% and a rolling speed of 0.117 m/s. Based on these results, rolling finite element simulations under total reduction–pass conditions of 65%–3 passes, 75%–4 passes, and 85%–5 passes were conducted on 20CrNiMo/Incoloy 825 composite materials. The rolling process was found to be optimal for a total reduction of 85%–5 passes based on the ratio of the vertical compressive stress experienced by the Incoloy 825-side metal to the yield strength of Incoloy 825 at 1150 °C. Based on the results of single- and multi-pass finite element simulation experiments, microstructural observations and interface analyses were then conducted on the 20CrNiMo/Incoloy 825 composite materials after rolling. The bonding interface of the composite materials was found to be undulating, indicating good composite effects. In addition, Cr, Ni, and Fe at the interface of the composite materials exhibited a steep gradient of change, indicating trace element diffusion with a distance of 8.27 μm in the 20CrNiMo/Incoloy 825 composite materials. Finally, the interfacial bonding mechanism of the 20CrNiMo/Incoloy 825 composite materials was studied, and the results indicate that this mechanism is based on a combination of diffusion and recrystallization bonding mechanisms.

Rolling Contact Fatigue Behaviors of 20CrNi2Mo Steel by a New Carbon and Nitrogen Composite Infiltration Process

The high-cycle fatigue behavior of carburized M50NiL steel with high-energy modification and compound infiltration: A comparative study

Effects of carburizing and nitriding sequential treatment on rolling contact fatigue of M50NiL bearing steel

Rolling Contact Fatigue Performances Of Carburized And High-C Nanostructured Bainitic Steels

Rolling Contact Fatigue Failure Mechanism of Martensitic Bearing Steel after Carbonitriding

Carburization Induced Extra-Long Rolling Contact Fatigue Life of High Carbon Bearing Steel

Rolling contact fatigue behaviors of 25CrNi2MoV steel combined treated by discrete laser surface hardening and ultrasonic surface rolling

Low Cycle Fatigue and Creep Fatigue Interaction Behavior of 9Cr-0.5Mo-1.8w-v-nb Heat-Resistant Steel at High Temperature

Investigation into the Rolling Process of 20CrNiMo/Incoloy 825 Composite Materials

Surface integrity and rolling contact fatigue behavior of 18CrNiMo7-6 steel subjected to ultrasonic surface rolling process

Rolling Contact Fatigue Wear Behavior of Carbide-free Bainitic Steel

Microstructures and rolling contact fatigue behaviors of 17Cr2Ni2MoVNb steel under combined ultrasonic surface rolling and shot peening

Microstructural evolution and performance change of a carburized nanostructured bainitic bearing steel during rolling contact fatigue process

Rolling Contact Fatigue and Sliding Wear Performance of Ferritic Nitrocarburized M-50 Steel

The influence of carbon content on the microstructure, mechanical and frictional property of chromium carbon nitride composite films

Microstructure, Adhesion and Tribological Properties of CrN/CrTiAlSiN/WCrTiAlN Multilayer Coatings Deposited on Nitrocarburized AISI 4140 Steel

Experimental Study on the Influence of Surface Carbon Content on Crack Initiation for 20Cr2Ni4A Steel

Improved Rolling Contact Fatigue Life for an Ultrahigh-Carbon Steel with Nanobainitic Microstructure

Fatigue behaviors of 40Cr steel bars after nitriding-ultrasonic impacting compound strengthening treatment

Relating rolling contact fatigue (RCF) life to the microstructure evolution in aerospace grade bearing steels: A comparison of Cronidur-30 with AISI 440C