Abstract:In this study, structural, morphological, thermal and magnetic properties of amorphous-nanocrystalline Fe 70 Cr 10 Nb 10 B 10 (at.%) alloy are discussed. The formation and evaluation of amorphous-nanocrystalline structures of the alloy were followed by XRD, SEM-EDX, TEM, DTA, and VSM techniques. After 50 h of milling Cr, Nb, and B were completely dissolved into the Fe lattice forming 82% of the amorphous phase of the alloy. A gradual dissolution of the alloying elements also increased the lattice parameters concurrently. The lattice parameters reached a maximum value of 2.908 Å after 20 h of milling and then leveled off to a value of 2.891 Å at the end of 50 h of milling. Based on the XRD data, crystallite size and lattice strain of the alloy were calculated as 3.2 nm and 3.34% respectively. TEM analyses revealed that the alloy particulates comprised needle-shaped nanoparticles of an average size of 21 nm. The room temperature magnetic hysteresis loops showed that the increased duration of milling decreased the saturation magnetization from 91 to 24 emu/g. This was mainly due to the upsurge on the amorphous phase content in the alloy as the milling progressed. The increase in amorphous phase content and the subsequent reduction of the saturation magnetization were due to the inter-diffusion of the non-ferromagnetic Cr and B atoms into the Fe lattice. Thermal studies revealed that around 350 °C the amorphous phase of the alloy began crystallizing. The magnetic saturation of the heat-treated alloy also increased with the growth in the crystalline phases. The 50 h milled sample annealed at 700 °C was found to have the highest magnetic anisotropy as observed from the temperature-dependent zero-field cooled and field cooled magnetization measurements. The high-pressure X-ray diffraction measurements revealed that the amorphous state of the alloy remained stable up to 11.3 MPa. It also revealed the structural similarities of the Fe 70 Cr 10 Nb 10 B 10 alloy with those of the Fe 70 M 10 B 20 (M = Nb and Cr) types. For all practical purposes, the microstructural stability under high compressive pressure represents the consolidation properties of the nanostructured magnetic materials since both pressure and temperature-induced phase transformations are the primary controlling factors for the specific magnetization properties of the alloy.

Structure and mechanical properties of nanostructured Rhombohedral Cr5Al8

Structure and mechanical properties of nanostructured Rhombohedral Cr<sub>5</sub>Al<sub>8</sub>

Effect of Cr on solidification structure and microhardness of Al-Ni alloy

First-principles Study of the Structural and Elastic Properties of Cr2AlX (X=N, C) Compounds

Microstructure and mechanical properties of lightweight Al<i><sub>x</sub></i>CrNbTiV(<i>x</i>=0.2, 0.5, 0.8) refractory high entropy alloys

Microstructure and strengthening mechanisms of novel lightweight TiAlV0.5CrMo refractory high-entropy alloy fabricated by mechanical alloying and spark plasma sintering

Mechanical properties of NiAl–Cr alloys in relation to microstructure and atomic defects

Microstructure and mechanical properties of lightweight Al CrNbTiV(x = 0.2, 0.5, 0.8) refractory high entropy alloys

Microstructure, mechanical properties, electrical resistivity, and corrosion behavior of (AlCr) x (HfMoNbZr) 1-x films

Mechanical properties of Nb based multiphase alloy studied by nanoindentation and atomic force microscopy

Synthesis and characterization of amorphous-nanocrystalline Fe70Cr10Nb10B10 powders by mechanical alloying

Microstructural evolution and thermal stability in a nanocrystalline lightweight TiAlV0.5CrMo refractory high-entropy alloy synthesized by mechanical alloying

Microstructure Evolution and Mechanical Properties of As-Cast and Ultrasonic Treated Nb-16Si-xCr Alloys

Synthesis and Mechanical Properties of High-Purity Cr2alc Ceramic

Nanocrystalline Composites with High Strength Obtained in Zr–Ti–Ni–Cu–Al Bulk Amorphous Alloys

Symbiotically engineered crystalline-amorphous nanostructure in a strong-yet-stable Al alloy with large twinning-induced plasticity

High-strength and tunable plasticity in sputtered Al–Cr alloys with multistage phase transformations

Fabrications and mechanical properties of bulk amorphous, nanocrystalline, nanoquasicrystalline alloys in aluminum-based system

Mechanical Characterization and Deformation Behavior of Β-Stabilized Ti-Nb-Sn-Cr Alloys

Mechanical properties and fracture behaviour of nanostructured and ultrafine structured TiAl alloys synthesised by mechanical milling of powders and hot isostatic pressing

High Strength Aluminium Alloys Prepared by Nanocrystallisation of Amorphous Powders Using Spark Plasma Sintering