Abstract:At present, there is a great interest in the development of new airfoils for wind turbines and high-lift wings of unmanned aerial vehicles (UAV). The requirements for such airfoils differ from conventional aircraft airfoils, because of structural reasons and extreme operating conditions. So, wind turbine airfoils operate frequently under fully separated flow when stall is used for power regulation at high wind speeds. At the same time design of airfoils for wings UAV poses the problem of availability of high-lift at low Reynolds number. Modern airfoils are to a large extent developed from numerical methods. However, the complex flow conditions such as separation at high angles of attack, laminar separation bubbles and the transition from laminar to turbulent flow are difficult to predict accurately. Hence, testing of airfoils at a two-dimensional condition is an important phase in airfoil design. The development and validation of a 2D testing facility for investigation of single and multi-element airfoils in the wind tunnel Т-102 with open test section are considered in this article. T-102 is a continuous-operation, closed-layout wind tunnel with two reverse channels. The test section has an elliptical cross-section of 4 ×2,33 m and a length of 4 m. Two big flat panels of the L × H=3 ×3,9 m size installed upright on balance frame aligned with the free stream are used for simulating two-dimensional flow in the tunnel test section. The airfoil section in the layout of a rectangular wing is mounted horizontally between flat panels with minimum gaps to ensure 2D flow conditions. The aerodynamic forces and pitch moment acting on the model were measured by wind tunnel balance. To determine boundary corrections for a new test section of wind tunnel, the experimental investigation of three geometrically similar models has been executed. The use of boundary corrections has provided good correlation of the test data of airfoil NACA 6712 with the results obtained from the wind tunnel except for lift and drag coefficient values at high angles of attack.

Low-speed characteristics of four cambered, 10-percent-thick NACA airfoil sections

Effect of thickness, camber, and thickness distribution on airfoil characteristics at Mach numbers up to 1.0

Numerical and Experimental Research of Flow Control on an NACA 0012 Airfoil by Local Vibration

An investigation on the effect of second-order additional thickness distributions to the upper surface of an NACA 64 sub 1-212 airfoil

Influence of Relative Thickness on Static and Dynamic Stall Characteristics and Prediction of Airfoils

Direct numerical simulation of cambered airfoil aerodynamics at Re = 20,000

Optimizing NACA Airfoil Thickness Function Parameters for Maximum Lift-to-Drag Ratio

EXPERIMENT AND ANALYSIS OF AERODYNAMIC PERFORMANCE FOR CAS THIN AIRFOILS USED OF WIND TURBINE BLADES

Experimental investigation of multi-step airfoils in low Reynolds numbers applications

Comparative Assessment on Unsteady Aerodynamics of Thin and Thick Airfoils Subjected to Pitching Motion

Dynamic Thin-Airfoil Stall and Leading-Edge Stall of Oscillating Wings at Low Reynolds Number

Numerical and Experimental Investigation of a NACA 64A-110 Airfoil in Transonic Flow Regime

Study on Airfoils and Aerodynamics of High-Speed Aircraft Propeller

Computational and experimental study on the aerodynamic performance of NACA 4412 airfoil with slot and groove

Theoretical effect of modifications to the upper surface of two NACA airfoils using smooth polynomial additional thickness distributions which emphasize leading edge profile and which vary linearly at the trailing edge

Ordinates and Theoretical Pressure-distribution Data for NACA 6- and 6a-series Airfoil Sections with Thicknesses from 2 to 21 and from 2 to 15 Percent Chord, Respectively

Investigation of passive flow control over an airfoil using leading edge tubercles

Effects of Trailing Edge Thickness on NACA 4412 Airfoil Performance at Low Reynolds Numbers: A CFD Analysis

The Ultra-Low Reynolds Number Airfoil Wake

SIMULATION OF 2D FLOW AROUND OF AIRFOILS AT LOW-SPEED WIND TUNNEL WITH OPEN JET TEST-SECTION

Experimental characterization of turbulent boundary layers around a NACA 4412 wing profile