Abstract:Single crystal elastic constants of Ti–Ni alloys without (quenched) and with (aged) Ti3Ni4 precipitates were measured systematically by rectangular parallelepiped resonance method as a function of composition and temperature, and compared with Ti–Ni–Cu and Ti–Ni–Fe alloys, in an attempt to answer some long-standing questions as to the origin of the unique monoclinic B19′ martensite, and why composition and thermomechanical treatment greatly changes the path of martensitic transformation. The results showed that softening in c44, in additional to c′, is a common feature for all Ti–Ni binary (both quenched or aged) and ternary alloys. This general feature just corresponds to the fact that all these alloys ultimately transform into B19′, suggesting that softening in c44 is responsible for the unique B19′ martensite, which found no analogy in other β phase alloys. We also found an interesting correspondence between the temperature dependence of anisotropy factor and transformation path. Prior to B2–B19′ transformation anisotropy shows a decrease with lowering temperature; prior to B2–B19 an anisotropy increase, while prior to B2–R transformation a constant anisotropy. We further showed that three possible martensite candidates (R, B19, B19′) are rooted in anomalies in specific phonon modes and elastic softening. We showed that the multi-stage transformations are restricted by a general rule: multi-stage transformation occurs in the sequence of increasing transformation strain. With this rule we can explain all known transformation paths by considering the effect of alloying addition and fine precipitates/dislocation network on relative stability of different martensites. We further predict that there may exist a new transformation path in Ti–Ni-based alloys: B2–R–B19–B19′.

Identification of B33 and Cm martensitic products in CuZr-based alloys: A DFT study

Stress-induced phase stabilization and transformation in equiatomic CuZr B19’ martensite: A DFT study

Theoretical Investigation of Cu Influence on the Stability Characteristics of T-phase in Crossover Alloys

Microstructure and Phase Transformation of Ni46Mn33Ga17Cu4−xZrx Alloys

Group Theory and Crystallography of the Martensitic Transformation in a Cu-26.71Zn-4.15Al Shape Memory Alloy

In situ high-energy X-ray diffraction study of thermally-activated martensitic transformation far below room temperature in CuZr-based bulk metallic glass composites

Effect of Zr addition on the microstructure, phase transformation and mechanical property of Ni 50 Mn 25 Ga 17 Cu 8 alloy

Martensite structure and phase transformation of quaternary ZrCuAlCo high temperature shape memory alloys

Different phase transformation behaviors of B2-CuZr crystalline phase and their associated mechanical properties by molecular dynamics using different potentials

Analysis of phases in a Cu–Cr–Zr alloy

On mechanism underlying pure bainitic transformation

Fracture Behavior and Structural Transition of Ni46Mn33Ga17Cu4−Zr Alloys

Solidified microstructure and Phase equilibria of the Cu–Cr–X (X=Mg, Y) ternary systems

The structure and mobility of the intervariant boundaries in 18R martensite in a Cu–Zn–Al alloy

Solidification Paths and Phase Components at High Temperatures of High-Zn Al-Zn-Mg-Cu Alloys with Different Mg and Cu Contents

A Comparative Study of Elastic Constants of Ti–Ni-based Alloys Prior to Martensitic Transformation

Quantitatively Determining the Martensitic Transformation in a CuZr-based Bulk Metallic Glass Composite

Substructure and Interface of the Superstructure Martensite in Zr50Cu50 High Temperature Shape Memory Alloy

The pre-bainitic transformation in CuZnAlMn alloy

Mechanical Properties of the (Ti0.615zr0.385)100-3.9X(cu2.3fe1.6)x Alloys Containing Amorphous Martensite

The Influence of Cu on Martensite Phase Transition of High Temperature Shape Memory Alloy