Abstract:Titanium and its alloys have superior electrochemical properties compared to other alloy systems due to the formation of a protective TiO2 film on metal surfaces. The ability to generate the protective oxide layer will depend upon the type of alloy to be used. The aim of this work was to characterize the electrochemical corrosion behavior of titanium Ti-CP2 and alloys Ti-6Al-2Sn-4Zr-2Mo, Ti-6Al-4V, and Ti Beta-C. Samples were anodized in 1 M H2SO4 and H3PO4 solutions with a current density of 0.025 A/cm2. Electrochemical tests on anodized alloys were carried out using a three-electrode cell and exposed in two electrolytes, i.e., 3.5 wt % NaCl and 3.5 wt % H2SO4 solutions at room temperature. Scanning electron microscopy (SEM) was used to observe the morphology of anodized surfaces. The electrochemical techniques used were cyclic potentiodynamic polarization (CPP) and electrochemical noise (EN), based on the ASTM-G61 and G199 standards. Regarding EN, two methods of data analysis were used: the frequency domain (power spectral density, PSD) and time-frequency domain (discrete wavelet transform). For non-anodized alloys, the results by CCP and EN indicate icorr values of ×10−6 A/cm2. However, under anodizing conditions, the icorr values vary from ×10−7 to ×10−9 A/cm2. The PSD Ψ0 values are higher for non-anodized alloys, while in anodized conditions, the values range from −138/−122 dBi (A2·Hz−1)1/2 to −131/−180 dBi (A2·Hz−1)1/2. Furthermore, the results indicated that the alloys anodized in the H3PO4 bath showed an electrochemical behavior that can be associated with a more homogeneous passive layer when exposed to the 3.5 wt % NaCl electrolyte. Alloys containing more beta-phase stabilizers formed a less homogeneous anodized layer. These alloys are widely used in aeronautical applications; thus, it is essential that these alloys have excellent corrosion performance in chloride and acid rain environments.

Electrochemical Polishing of Additively Manufactured Ti–6Al–4V Alloy

Electrochemical Polishing of Additively Manufactured Ti–6Al–4V Alloy

Electropolishing of Additively Manufactured Ti-6Al-4V Surfaces in Nontoxic Electrolyte Solution

Electropolishing Mechanism of Ti-6Al-4V Alloy Fabricated by Selective Laser Melting

Electrochemical Polishing of Ti and Ti6Al4V Alloy in Non-Aqueous Solution of Sulfuric Acid

Electrochemical Polishing Method for Titanium Alloys with a Microgroove Structure

Electropolishing with Low Mass Loss for Additive Manufacturing of Ti6Al4V in Zinc Chloride-Urea Deep-Eutectic Solvent

Surface Finishing of 3D-Printed Ti-6Al-4 V Alloy by Electrolyte Plasma Polishing: Process Optimization and Microstructure

Anodic behavior in AlCl3-EMIC ionic liquid of Ti6Al4V alloy and its application for enhancing the adhesion strength of aluminum coatings

Study on electrochemical polishing of TC4 alloy

Electrochemical polishing of Ti–13Nb–13Zr alloy

Plasma electrolytic polishing-induced surface chemical and structural evolutions of additively manufactured Ti-6Al-4 V coupons

Study on electrochemical polishing mechanism of TC4 titanium alloy

Electrochemical Corrosion of Titanium and Titanium Alloys Anodized in H2SO4 and H3PO4 Solutions

Electrochemical Corrosion Behaviors Before and after Laser Polishing of Additive Manufactured TC4 Titanium Alloy

Corrosion of an Additively Manufactured Ti6Al4V Alloy in Saline and Acidic Media

The effect of partial substitution of Ti with Zr, Cr or V in the Mg35Ti10Ni55 electrode alloy on its electrochemical performance

Material Characterization and Electrochemical Properties of Titanium Alloy 5553 Prepared by Selective Laser Melting as Processed and after Abrading and Polishing

Effect of Electrolytic Plasma Polishing on Surface Properties of Titanium Alloy

The Electropolishing of Additively Manufactured Parts in Titanium: State of the Art

Electropolishing influence on biocompatibility of additively manufactured Ti-Nb-Ta-Zr: in vivo and in vitro