Abstract:As there is a strong pressure in the EU to reduce CO2 emissions and overall fossil fuel consumption in the energy sector, many boilers are burning biomass instead of traditional fuels (coal, natural gas, oil, etc.). This is mainly due to the EU 2030 energy strategy, which commits Member States to reduce fossil fuel emissions by at least 40% (compared to the 1990 level) and to use at least 32% of renewable energy. The combustion of biomass containing aggressive elements such as chlorine or sulfur causes serious damage to various boiler components, with negative impacts such as reduced boiler lifetime, increased investments and maintenance costs, reduced availability, and others. These problems occur mainly in plants/boilers designed to burn coal and redesigned to burn biomass (straw, wood chips, wood pellets, etc.). In this paper, the corrosion resistance of heat coatings determined in long-term laboratory tests in an environment specifically corresponding to biomass flue gas is presented. These results can be used to design a suitable modification of existing coal boilers using conventional materials. The aim was to compare three completely different technologies currently available on local markets for the preparation of these coatings—thin wire arc spray (TWAS), high-velocity oxygen fuel (HVOF), and water-stabilized plasma. These coatings were compared with the base material of the boiler tubes—low alloyed steel 16Mo3 and high alloyed austenitic stainless steel AISI 310 as a more expensive option for retrofit. After 5000 h of exposure in an environment containing HCl and SO2, no cracks or structural defects were observed in any of the coatings, and the substrate material showed no signs of oxidation. All the tested coatings had higher corrosion resistance than the 16Mo3 material, and some of them presented a corrosion behavior close to that of the high alloy AISI 310 steel. Structurally and corrosion-wise, the thermally sprayed coating prepared by HVOF technology was the best of all tested materials.

Experimental investigations on the chlorine-induced corrosion of HVOF thermal sprayed Stellite-6 and NiAl coatings with fluidised bed biomass/anthracite combustion systems

Fabrication and Characterization of HVOF Sprayed CoNiCrAlY-6%Al2O3 Coating to Improve High-Temperature Oxidation Resistance

Wear Resistance of Stellite 6 Coatings at High Temperature

Corrosion Behavior of NiCrBSi Coatings Deposited by HVOF Spraying

High-Temperature Corrosion of Nickel-Based Coatings for Biomass Boilers in Chlorine-Containing Atmosphere

Effect of Pre-oxidation on High-Temperature Chlorine-induced Corrosion Properties of Air Plasma-Sprayed Ni-5%Al Coatings

Comparative investigation on thermal corrosion of alloy coatings in simulated waste incinerator environment

Microstructure, hardness, and wear resistance at room and high temperature of Stellite-6/WC-6Co coatings deposited by laser cladding process

Mechanism of coupling corrosion caused by flue gas and deposits in municipal solid waste incinerator: Resistance of HVOF-NiCr coating

Effects of Reactive Element Oxides on the Isothermal Oxidation of Β-Nial Coatings Fabricated by Spark Plasma Sintering

High-temperature wear behavior of HVOF sprayed, laser glazed, and laser cladded Stellite 6 coatings on stainless steel substrate

Effects of Ni-5 wt% Al/Bi2O3 addition and heat treatment on mechanical and tribological properties of atmospheric plasma sprayed Al2O3 coating

Comparative Study on the Microstructure and Properties of 304 Stainless Steel Coatings Prepared by High-Velocity Oxygen Fuel Spraying and Air Plasma Spraying

Experimental Investigations on Erosion-Corrosion Characteristics of HVOF-Sprayed WC-10% Ni Coatings Deposited on Aluminum Alloy

Study of KCl-induced hot corrosion behavior of high velocity oxy-fuel sprayed NiCrAlY and NiCrBSi coatings deposited on 12CrMoV boiler steel at 700 °C

Studies on Corrosion Behavior of a Single-Crystal Superalloy and Its Sputtered Nanocrystalline Coatings with Solid NaCl Deposit in O2 + 38 Vol.% H2O Environment at 700 °C

Effect of Stellite12 and NiCrBSi HVOF coatings on the tribological behavior of CrN PVD film

Microstructure, hardness and slurry erosion-wear behaviors of high-speed laser cladding Stellite 6 coatings prepared by the inside-beam powder feeding method

Corrosion and erosion performance of HVOF/TiAlN PVD coatings and candidate materials for high pressure gate valve application

Wear and Corrosion of HVAF and HVOF-Sprayed WC-CoCr Coatings on Aluminum Alloy

High-Temperature Erosion of HVOF Sprayed Cr 3 C 2 -NiCr Coating and Mild Steel for Boiler Tubes