Abstract:The external heat transfer mechanisms acting on the external mold surfaces for equiaxed casting processes are very complex. The mechanisms are multi-mode, transient, and nonuniform, consisting of very complex radiative and convective definitions. In this work, a real-life mold, SGT6-5000 FD 3/4 Blade 4 cast in Alloy-247, was instrumented with thermocouples and temperature readings were recorded throughout the entire casting sequence of events. Analytical models based on the first law of thermodynamics, Fourier’s law, Newton’s Law of Cooling, and diffuse gray radiation for an N-sided enclosure were developed to use the thermocouple data as input to back calculate the emissivity of the mold, as well as the spatially varying heat transfer coefficients for a number of local regions. The derived external heat transfer mechanisms are presented as transient Biot numbers. The derived emissivity and nonuniform heat transfer coefficients for these surfaces were then validated in ProCAST numerical simulation by comparing the external mold temperature profiles. An extensive iterative, curve fitting, extrapolating, and averaging procedure was exercised to derive an expression for emissivity across the entire temperature range associated with the casting process. The predicted temperatures on the nodes corresponding to the thermocouple locations agree within reasonable error with the experimental data. The model also qualitatively predicted the shrinkage porosity detected via x-ray imaging for this casting. The current study confirms the hypothesis of previous work by the current authors with respect to the transient nonuniform boundary condition concept. Unique values of heat transfer coefficients were observed at different vertical positions along the airfoil. The analytical models were also able to capture phenomena associated with specific sequences of the casting process. This work provides the analytical models, and procedure, needed to derive these spatially varying conditions. The current authors contribute to the intellectual know-how of the large gas turbine casting industry which by other foundries is considered highly proprietary and strictly confidential. This paper should be used to set the precedence for how foundries derive and validate the external boundary conditions used in solidification process modeling.

Thermal Distortion Testing at Ferrous Superheat Temperatures

Design of a Test Rig for the Characterization of Thermal Fatigue and Soldering Resistance of the Surfaces of Tool Steels for High‐Pressure Die‐Casting Dies

Three Dimensional Dynamical Measurement of Distortion of Heavy Steel Castings During Heat Treatment Process

Integrated System of Thermal/Dimensional Analysis for Quality Control of Metallic Melt and Ductile Iron Casting Solidification

Development of an Experimental Setup to Investigate Influences on Component Distortion in Gravity Die Casting and a First Variation of Temperature Control Strategy

Investigating Thermal and Mechanical Characteristics of Die-Casting Aluminum Alloys: A Comprehensive Investigation via Thermal Analysis

Revisiting the Effect of Casting Thickness and Austempering Temperature of Gray Iron

Effect of melting temperature on microstructural evolutions, behavior and corrosion morphology of Hadfield austenitic manganese steel in the casting process

Development of Test Method for Measuring Sintering Temperature of Mould Fluxes

Distortion Behavior of Hydro Turbine Blade Castings During Heat Treatment Processes under Variation of Seasonal Temperature

Impact of Temperature of Cast Iron Chills on Tensile Properties in the Aluminum Precisions Sand Casting Process

Achieving Higher Strength and Ductility in Heavy-Section Ductile Iron Castings

Surface Temperature Difference for Analysis of Distortion of Heavy Weak-Rigidity Castings During Heat Treatment

Determination and Application of Thermophysical Properties of Heavy Steel Casting for Solidification Simulation

The Influence of Thermomechanical Conditions on the Hot Ductility of Continuously Cast Microalloyed Steels

Study on the High Temperature Deformation Measurement Using the Mark Shearing Technique

Mechanical Performance and Thermology Performance of 20crmo Steel at High Temperature

An Experimental Derivation of Transient Nonuniform External Boundary Conditions for the Solidification Process Modeling of Equiaxed Investment Castings

Computational Analysis of the Temperature Profile Developed for a Hot Zone of 2500°C in an Induction Furnace

Measurement of High Temperature Full-Field Strain Up to 2000 °C Using Digital Image Correlation

High-Temperature Properties of Mold Flux Observed and Measured in Situ by Single/Double Hot-Thermocouple Technique