Abstract:Using metals of the highest purity, the constitutions of iron-rich and manganese-rich binary alloys with the sequence of elements Ti-V-Cr-(Mn, Fe)-Co-Ni-Cu have been investigated by specially accurate thermal analysis, supplemented by microscopical and X-ray work. The liquidus and solidus curves have been determined accurately, and also the forms of the A 4 (Y/O) transformations in the iron alloys, and of the (Y/O) and (Y/B) transformations in the manganese alloys. The complete liquidus and solidus were determined for the system Fe—Mn, and the equilibrium diagrams of the systems Fe-Ti and Mn-Ti were studied as far as 52 at. % Ti. O-Mn (b.c.c.) and y-Mn (f.c.c.) have the same crystal structures as O-Fe and y-Fe respectively, and the corresponding parts of the equilibrium diagrams are thus structurally comparable. In general, there is a remarkable correspondence between the effects of the different elements in stabilizing the b.c.c. or f.c.c. phases. The closed y-loops in the systems Fe-Ti, Fe—V and Fe-Cr are paralleled by closed y-fields in the Mn alloys, whilst Mn (in Fe), Fe (in Mn) and Ni produce open or expanded y-fields; Cu behaves abnormally in both series of alloys. In the Mn alloys, the stability and range of the B-Mn phase reach a maximum in the system Mn-Co, where the B-Mn phase is so stable that it comes into equilibrium with the liquid, and prevents the formation of a continuous series of solid solutions between Y-Mn and B-Co (f.c.c.). For the iron alloys the size factors are favourable for all the solutes examined, except Ti, which lies on the borderline of the favourable zone. With O-Mn and Fe-Mn as solvents, the size factors are all favourable, although that for Ti is still appreciable ( ca. 10%). The effect of size factor is shown by steep depression of the O-liquidus and O-solidus curves in the systems Fe-Ti and Mn—Ti. For the iron alloys the relative depressions of liquidus and solidus at equal atomic percentages of solute are in the order Ti > V > Cr and Co < Ni < Cu, and these sequences are the same as those for the lattice distortions produced by equiatomic percentages of the same solutes; the effect of Mn lies out of sequence in both cases. These and other relations are discussed. When compared with previous diagrams, the general effect of the present work is to indicate a much narrower two-phase (liquid and solid) range for both O-Fe and Y-Fe solid solutions. In marked contrast to previous diagrams, the present liquidus and solidus curves can all be reconciled with the existence of monatomic solutions in both liquid and solid phases. For Fe-Mn alloys the equations for dilute solutions are in good agreement with thermal data for pure iron up to 30 at. % Mn.

Highly supersaturated Al-Mn solid solution alloys and their decomposition by heat-treatment

Effects of Solution Treatment on Microstructure and Properties of Al-Mg-Si-Mn alloy

Effect of Cu and Mn content on solidification microstructure, T-phase formation and mechanical property of Al Cu Mn alloys

Microstructure Evolution of Semi-Solid Mg-14Al-0.5Mn Alloys During Isothermal Heat Treatment

Effect of Mechanical Alloying on the Dissolution of the Elemental Mn and Al-Mn Compound in Aluminum

Influence of Mn Addition on the Microstructure and Mechanical Properties of a Directionally Solidified Γ-Tial Alloy

Study of supersaturated solid solution decomposition during quenching of sheets from Al-Mg-Si aluminum alloy

Effect of Fe and Mn Content on the Microstructures and Tensile Behaviour of AlSi7Cu3 Alloy: Thermal Analysis and Tensile Tests

Microstructure Formation of Al-Based Alloys in the Presence of Rare Earth Metals (Ce, La) and Mn under High Cooling Rate

Microstructures and Magnetic Properties of Rapidly Solidified MnAl Alloys Modified with Indium

The Effects of a Trace Amount of Manganese and the Homogenization on the Recrystallization of Al–7Mg–0.15Ti Alloys

The Structural and Magnetic Properties of Τ-Mnal Films Prepared by Mn/Al Multilayers Deposition Plus Annealing

Effect of Mn on the Elevated Temperature Mechanical Properties of Al-La Alloys

Effect of Mn/Ag Ratio on Microstructure and Mechanical Properties of Heat-Resistant Al-Cu Alloys

Decomposition of Supersaturated Solid Solution in Fast-Quenched Al-Co-Zr and Al-Fe-Co-Zr Alloys

The constitution of alloys of iron and manganese with transition elements of the first long period

Influence of Mn Addition on the Evolution of Precipitates in Al-Cu Alloys

Iron Intermetallic Phases in the Alloy Based on Al-Si-Mg by Applying Manganese

Study of Intergranular Corrosion Behaviors of Mn-Increased 5083 Al Alloy with Controlled Precipitation States of Al6Mn Formed during Homogenization Annealing

Effect of Mn‐bearing dispersoids on tensile properties and recrystallization resistance of Al‐3Mg‐0.8Mn rolled alloy

Microstructure evolution of a novel low-silicon cast aluminum alloy modified with Mn and Cr during solution treatment