Abstract:Due to a good combination of high hardness, wear resistance, toughness, resistance to high operating temperatures, and fairly low material cost, AISI H13 tool steel is commonly used in the manufacture of injection molds. Additive manufacturing (AM) such as selective laser melting (SLM), due to the layer-wise nature of the process, offers substantial geometric design freedom in comparison with conventional subtractive manufacturing methods, thereby enabling a construction of complex near-net shape parts with internal cavities like conformal cooling channels. The quality of SLM-manufactured parts mainly depends on the part geometry, build orientation and scanning strategy, and processing parameters. In this study, samples of H13 tool steel with a size of 10 × 10 × 15 mm3 were SLM-manufactured using a laser power of 100, 200, and 300 W; scanning speed of 200, 400, 600, 800, 1000, and 1200 mm/s; and hatch spacing of 80 and 120 µm. A constant layer thickness of 40 µm, 67° scanning rotation between subsequent layers, and a stripe scanning strategy were maintained during the process. The samples were built considering a preheating of 200 °C. The relative density, surface roughness, crack formation, microstructure, and hardness were evaluated. The relative density is shown to increase with increasing the volumetric energy density up to a value of about 60 J/mm3 and then no significant increase can be pointed out; the maximum relative density of 99.7% was obtained. A preheating of 200 °C generally aids to increase the relative density and eliminate the crack formation. The microstructure of built samples shows fine equiaxed cellular-dendritic structure with martensite and some retained austenite. The microhardness of the as-built samples was found to vary from 650 to 689 HV 0.2, which is comparable to a conventionally produced H13 tool steel.

Enhancing Mechanical Properties of Additively Manufactured H13: A Two-Step Approach Integrating Processing Parameters Optimization and a Tailored Heat Treatment

Mechanical Properties and Fracture Behavior of Laser Powder-Bed-Fused GH3536 Superalloy

Achieving Ultrahigh Yield Strength and Decent Toughness in an In-Situ Alloyed H13 Steel Via Laser Powder Bed Fusion

Effect of Different Post-Processing Thermal Treatments on the Fracture Toughness and Tempering Resistance of Additively Manufactured H13 Hot-Work Tool Steel

Process-structure-property Modeling for Postbuild Heat Treatment of Powder Bed Fusion Ti-6Al-4V

The enhancement of mechanical properties via post-heat treatments of AISI 630 parts printed with material extrusion

Additive Manufacturing of AISI H13 Tool Steel with Combinations of Higher Laser Power and Scan Speed: Microstructural and Mechanical Properties Insights

Post-Heat Treatment Design of High-Strength Low-Alloy Steels Processed by Laser Powder Bed Fusion

Effect of Heat Treatment on Microstructural Evolution, Mechanical Properties and Tribological Properties of H13 Steel Prepared Using Selective Laser Melting

Integration of additive manufacturing and thermomechanical processing toward a hybrid production route for PH13-8Mo stainless steel

Role of Direct Aging and Solution Treatment on Hardness, Microstructure and Residual Stress of the A357 (AlSi7Mg0.6) Alloy Produced by Powder Bed Fusion

Superior strength-ductility in laser aided additive manufactured high-strength steel by combination of intrinsic tempering and heat treatment

Effect of Heat Treatment on the Anisotropy in Mechanical Properties of Selective Laser Melted AlSi10Mg

Exceptional strength-ductility synergy in additively manufactured (CoCrNi)90Al5Ti5 medium-entropy alloy by heat treatment

Process-Structure-Property Relationships of AISI H13 Tool Steel Processed with Selective Laser Melting

Process for achieving 2000 MPa H13 steel by eliminating temper embrittlement

Microstructure Tailoring for High Strength Ti-6Al-4V without Alloying Elements through Optimized Preheating and Post-Heating Laser Scanning in Laser Powder Bed Fusion

Enhancement of an additive-manufactured austenitic stainless steel by post-manufacture heat-treatment

Mechanical Properties of AlSi10Mg Processed by Laser Powder Bed Fusion at Elevated Temperature

Programmable mechanical properties of additively manufactured novel steel

Simultaneous enhancements of strength and ductility of a selective laser melted H13 steel through inoculation treatment