Abstract:This manuscript reports an approach for additive manufacturing of complex functionally‐graded metallic components via laser powder bed fusion, where the composition and volume fractions of the phases are locally tuned via spatial modulation of the processing parameters. Hybrid structures made of 17‐4PH steel, with local variations of ~20% in strength and ~150% in ductility are demonstrated. The established approach to materials design for additive manufacturing (AM) consists of attempting to reproduce the uniform structures and properties of conventionally processed materials. While this certainly helped facilitate material certification and the rapid introduction of AM technologies in several industries, the opportunity to exploit unique features of specific AM processes to generate spatially varying microstructures–and hence novel materials, remains largely untapped. This work presents a method for manufacturing materials through laser powder bed fusion (LPBF), in which control over the spatial variation in phase composition and mechanical properties is achieved. This technique is demonstrated using 17‐4 precipitation‐hardened stainless steel (17‐4PH), by controlling spatial modulation of energy densities during printing. This results in local control of ferrite/martensite volume fractions, allowing the fabrication of metal/metal architected composites with hard/brittle regions interspersed with soft/tough regions. Local variations of ~20% in tensile strength and ~150% in elongation are achieved, with a spatial resolution of ~100 microns. The approach is general and robust, fully compatible with commercially available LPBF equipment, and applicable to virtually any multi‐phase alloy system. This work shifts the paradigm from attempting to print components with uniform properties to manufacturing alloys with controlled spatial property gradients.

Integration of additive manufacturing and thermomechanical processing toward a hybrid production route for PH13-8Mo stainless steel

Effects of Additive Manufacturing Processes and Isothermal Aging on the Microstructure and Properties of 13-8 Mo Precipitation Hardening Martensitic Stainless Steel

A new high-throughput method using additive manufacturing for alloy design and heat treatment optimization

Enhancing Mechanical Properties of Additively Manufactured H13: A Two-Step Approach Integrating Processing Parameters Optimization and a Tailored Heat Treatment

Microstructural Control of a Multi‐Phase PH Steel Printed with Laser Powder Bed Fusion

Role of Direct Aging and Solution Treatment on Hardness, Microstructure and Residual Stress of the A357 (AlSi7Mg0.6) Alloy Produced by Powder Bed Fusion

Additive manufacturing of alloys with programmable microstructure and properties

The influence of post-thermal treatments on microstructure and mechanical properties in A20X alloy fabricated through powder bed fusion

Additively manufacturable high-strength aluminum alloys with thermally stable microstructures enabled by hybrid machine learning-based design

Development of post-treatment for enhanced performance of an additively manufactured Alloy 718

The impact of heat treatment on microstructure, residual stress, and mechanical behavior of laser powder bed fusion additively manufactured Ti–6Al–2Sn–4Zr–2Mo alloy

Programmable mechanical properties of additively manufactured novel steel

Processing of High Interstitial Austenitic Steel with PBF‐LB/M‐Evolution of chemical inhomogeneity and microstructural features during Post‐Processing

Micromechanical Modeling of AlSi10Mg Processed by Laser-Based Additive Manufacturing: From as-Built to Heat-Treated Microstructures

Effect of homogenization on precipitation behavior and strengthening of 17-4PH stainless steel fabricated using laser powder bed fusion

Rapid Alloy Development Using Calphad Simulation and Powder Blends in Direct Energy Deposition

Processing-microstructure relationships in ferrous alloys via mixed powder laser powder bed fusion

Homogenization timing effect on microstructure and precipitation strengthening of 17–4PH stainless steel fabricated by laser powder bed fusion

Development of computational framework for titanium alloy phase transformation prediction in laser powder-bed fusion additive manufacturing

A Novel Approach for Enhanced Mechanical Properties in Solid-State Additive Manufacturing by Additive Friction Stir Deposition Using Thermally Stable Al-Ce-Mg Alloy

Thermo-mechanical simulation of annealing heat treatment of Ni-based GH4099 superalloy made by laser powder bed fusion