Abstract:Statement of problem: Strength-gradient zirconia combining 3 zirconia formulations with different flexural strengths has been reported to have outstanding mechanical properties. However, data concerning the effect of different sintering protocols on the fracture strength of 3-unit monolithic gradient zirconia fixed partial dentures (FPDs) are sparse. Purpose: The purpose of this in vitro study was to test the effect of different sintering protocols on the fracture strength of 3-unit monolithic gradient zirconia FPDs. Material and methods: Two custom-made stainless-steel master dies were designed to replicate a mandibular right second premolar and second molar prepared to receive a 3-unit monolithic zirconia FPD. Thirty monolithic zirconia FPDs were milled from gradient zirconia blanks and allocated to 3 groups (n=10) according to the sintering protocols: high-speed sintering, speed sintering, and conventional sintering. The FPDs were cemented onto the corresponding dies with traditional glass ionomer cement. All FPDs were cyclic loaded (600 000 cycles/49 N/1.7 Hz) in a mastication simulator. Fracture load measurements for each FPD were determined by using a universal testing machine. Scanning electron microscopy (SEM) at ×80 magnification was used to examine a fractured FPD from each group. A representative specimen from each group was examined with SEM at ×30 000 magnification to determine the grain size. One-way ANOVA, pair-wise Tukey honestly significant difference (HSD), and Pearson correlation tests were used for statistical analysis of the data (α=.05). Results: The high-speed sintered FPDs recorded the highest statistically significant fracture load mean ±standard deviation value (2526 ±300 N), followed by the speed sintered FPDs (2136 ±127 N), while the lowest statistically significant fracture load mean value was recorded with the conventionally sintered FPDs (1361 ±181 N) (P<.001). In addition, the mean ±standard deviation grain size values were 488 ±272 nm for the high-speed sintered specimen, 578 ±409 nm for the speed sintered specimen, and 832 ±551 nm for the conventionally sintered specimen (P<.001). A significant negative correlation was found between fracture strength and grain size among the 3 groups. Conclusions: The fracture strength of 3-unit monolithic gradient zirconia FPDs sintered by using a high-speed protocol was significantly higher than that of speed and conventionally sintered FPDs (P<.001). The high-speed sintering protocol reduced the mean grain size of gradient zirconia FPDs compared with that of both speed and conventional sintering protocols.

Effect of sintering cycle on the strength and translucency of multilayered zirconia

Influence of Restoration Thickness and Resin Cement on Translucency and Color of Different Types of Monolithic Zirconia and Lithium Disilicate Ceramic

EVALUATION OF BIAXIAL FLEXURAL STRENGTH AND TRANSLUCENCY OF MULTICHROMATIC TRANSLUCENT ZIRCONIA AND LITHIUM DISILICATE CERAMICS

Effect of speed sintering process on the microstructure, flexural strength and translucency of zirconia

Effect of different sintering protocols on the fracture strength of 3-unit monolithic gradient zirconia fixed partial dentures: An in vitro study

Current speed sintering and high-speed sintering protocols compromise the translucency but not strength of yttria-stabilized zirconia

Impact of the sintering parameters on the grain size, crystal phases, translucency, biaxial flexural strength, and fracture load of zirconia materials

Optical and Mechanical Properties of the Multi‐Transition Zones of a Translucent Zirconia

Effect of High-Speed Sintering on the Optical Properties, Microstructure, and Phase Distribution of Multilayered Zirconia Stabilized with 5 mol% Yttria

Translucency of chairside monolithic zirconias using different sintering ovens: An in vitro investigation

TRANSLUCENCY EVALUATION OF ZIRCONIA LITHIUM SILICATE AND LITHIUM DISILICATE GLASS CERAMIC WITH DIFFERENT THICKNESSES PRE AND POST CEMENTATION

Mechanical Properties of Zirconia Materials with Different Translucency: An In Vitro Study

The effect of surface treatment and low-temperature degradation on flexural strength of additive manufactured zirconia

Randomized clinical trial of zirconia laminate veneers sintered by using conventional versus speed process: 1-year follow-up

Research of Optical Properties and Biocompatibility in Different Zones of Multilayered Translucent Zirconia on Hydrothermal Aging

Layer characteristics in strength-gradient multilayered yttria-stabilized zirconia

Effect of coloring and sintering on the translucency and biaxial strength of monolithic zirconia

Effects of thickness and polishing treatment on the translucency and opalescence of six dental CAD-CAM monolithic restorative materials: an in vitro study

The effect of speed sintering on the optical properties and microstructure of multi‐layered cubic zirconia

Mechanical and optical properties of multilayer yttria-stabilized zirconia for dental prostheses

In Vitro Evaluation of Speed Sintering and Glazing Effects on the Flexural Strength and Microstructure of Highly Translucent Multilayered 5 mol% Yttria-Stabilized Zirconia