Abstract:Objectives: Firing protocols influence optical properties of dental ceramics. Effects of varying cooling rates of monochrome and multilayer 5 mol% yttria-stabilized tetragonal polycrystalline (5YTZP) on optical properties are subjected for investigation. Materials and methods: Ninety specimens (width, length, thickness = 10 × 20 × 2 mm) were prepared from monochrome (Mo: Cercon xt) and multilayer (Mu: Cercon xt ML with cervical (C) and incisal (I) zoning) 5YTZP. Specimens were sintered and randomly treated with three cooling rates (n = 15/group): slow (S: 5°C/min), normal (N: 35°C/min), and fast (F: 70°C/min). Color appearance (∆EW), color appearance difference (∆E diff), translucency parameter (TP), contrast ratio (CR), and opalescence parameter (OP) were evaluated in CIEL*a*b* (Commission International de I'Eclairage) system. ∆E diff was achieved from the coordinate difference of specimen to VITA classic shade A2. Microstructures and compositions were evaluated by scanning electron microscope and energy dispersive spectroscopy. Monoclinic (m), tetragonal (t), and cubic (c) phases were investigated with X-ray diffraction. Statistical analysis: An analysis of variance and Bonferroni multiple comparisons were determined for significant differences (p < 0.05). Results: ΔEW of MoF was highest (66.04 ± 1.86), while MuN-I was lowest (62.60 ± 0.86). TP and OP of MoS were highest at 2.85 ± 0.11, and 2.25 ± 0.10, while MuF-I was lowest at 2.16 ± 0.10 and 1.60 ± 0.12. CR of MuF-I was highest (0.948 ± 0.005), while MoS was lowest (0.936 ± 0.005). ΔEdiff of MoF was highest (3.83), while MuN-I was lowest (0.93). Limited grain growth and m-phase composition were indicated upon fast cooling. There were significant differences for all color parameters due to varied materials, cooling rates, and their interactions (p < 0.05) except for interaction in ∆EW and OP. Conclusions: Translucency of monochrome and multilayer 5YTZP were different, possibly due to colorant additives. Incisal layer of multilayer 5YTZP was perfectly matched with VITA shade. Increasing cooling speed resulted in smaller grain size, t-m transformation, and finally lower translucency and opalescence. Therefore, to achieve most favorable optical properties, slow cooling rate is recommended.

The effect of speed sintering on the optical properties and microstructure of multi‐layered cubic zirconia

Effect of speed sintering process on the microstructure, flexural strength and translucency of zirconia

Effect of High-Speed Sintering on the Optical Properties, Microstructure, and Phase Distribution of Multilayered Zirconia Stabilized with 5 mol% Yttria

Influence of Restoration Thickness and Resin Cement on Translucency and Color of Different Types of Monolithic Zirconia and Lithium Disilicate Ceramic

Optical Properties of Zirconia Monolithic Crowns Constructed Using Speed Sintering Cycle

Effect of Machining Method and Margin Design on the Accuracy and Margin Quality of Monolithic Zirconia Crowns

Does speed-sintering affect the optical and mechanical properties of yttria-stabilized zirconia? A systematic review and meta-analysis of in-vitro studies

Optical Characteristics of Monochrome and Multilayer Fully Stabilized Zirconia Upon Sintered Cooling Speed

In Vitro Evaluation of Speed Sintering and Glazing Effects on the Flexural Strength and Microstructure of Highly Translucent Multilayered 5 mol% Yttria-Stabilized Zirconia

Effect of Chairside Rapid Sintering Process on Microstructure and Mechanical Properties of TZP Zirconia Ceramics

Impact of the sintering parameters on the grain size, crystal phases, translucency, biaxial flexural strength, and fracture load of zirconia materials

Current speed sintering and high-speed sintering protocols compromise the translucency but not strength of yttria-stabilized zirconia

Effect of sintering cycle on the strength and translucency of multilayered zirconia

Effect of sintering procedures on optical properties, chemical composition, and grain size of monolithic zirconia ceramic at different thicknesses after hydrothermal aging: An in vitro study

Randomized clinical trial of zirconia laminate veneers sintered by using conventional versus speed process: 1-year follow-up

Conventional sintering of nano-crystalline Yttria-Stabilized Zirconia enables high-strength, highly translucent and opalescent dental ceramics

Effect of Milling Speed on the Properties of Zirconia Restorations

Optical and Mechanical Properties of the Multi‐Transition Zones of a Translucent Zirconia

Optical properties evaluation of rapid sintered translucent zirconia with two dental colorimeters

Translucency of chairside monolithic zirconias using different sintering ovens: An in vitro investigation

Effect of glass infiltration and modified cooling rates on color characteristics alteration of monochrome and multilayer high yttrium oxide containing zirconia