Abstract:AISI 52100 steel has been widely used in the mechanical industry due to its excellent mechanical properties and high availability. In some cases, an ultra-smooth surface of AISI 52100 steel is needed and is even indispensable for the satisfactory performance of devices. In this paper, chemical mechanical polishing technique was employed to prepare the ultra-smooth surface of AISI 52100 steel. Colloidal silica was used as the abrasive. The effects of pH, complexing agent such as glycine, H2O2 and benzotriazole (BTA) on the polishing performance were studied. It is revealed that, with the increase of pH, the static etching rate (SER) and the material removal rate (MRR) are both gradually reduced, and the post-CMP surface roughness I?, decreases. This is attributed to the fact that compact and passive iron oxides, especially Fe(III) oxides, gradually form on the top surface. At pH 4.00, in the presence of glycine, and with the increase of the H2O2 concentration, the SER is further suppressed, and the surface roughness R-a gradually decreases; the MRR initially dramatically increases due to the fact that, with the addition of small amount of H2O2, the porous iron oxide layer with relatively low mechanical strength can be rapidly formed on the surface. Moreover, glycine intensifies the chemical dissolution by chelating iron ions, especially Fe(II) ions, and thereby the mechanical strength of the oxide layer further weakens. Then, after reaching the peak value, the MRR gradually decreases when the H2O2 concentration further increases since the compactness of the oxide layer gradually increases. With the increase of the BTA concentration, the MRR is gradually suppressed and the surface roughness R-a decreases due to the formation of Fe-BTA passivating film on the top surface. Finally, a two-step polishing process was developed. The polishing results show that, within 20 min, a rough surface of AISI 52100 steel with the R-a value of 188 nm can be polished into an ultra-smooth surface with the R-a value of 1.8 nm. (C) 2015 Elsevier B.V. All rights reserved.

Optimization of the process for combined electrochemical and mechanical polishing of 45 steel

Experimental Research on Optimizing Processing Parameters of Ultrasonic Polishing without Abrasive

Chemical Mechanical Polishing of Steel Substrate Using Colloidal Silica-Based Slurries

A novel process of chemical mechanical polishing for FV520B steel

Achieving a super-smooth surface of stainless bearing steel with chemical mechanical polishing via controlling corrosive wear of Fe and Cr

DEVELOPNENT OF THE TECHNOLOGICAL PARAMETERS OF ELECTROCHEMICAL POLISHING OF THE ST 20 GRADE STEEL

Research on the surface characteristics of 42CrMo alloy steel pulse electrochemical machining

Novel rotary chemical mechanical polishing on an integral impeller

A novel high-quality and high-efficiency immersion fluid chemical mechanical polishing process for integral impellers

Parameters optimization of electrolytic plasma polishing of austenitic stainless steel and surface performance analysis

Study on electrochemical mechanical polishing process of silicon carbide crystal

Enhancing Chemical Mechanical Polishing Efficiency of Steel with Sulfate

Impurity-free and high-efficiency modification for 30CrMo steel

Technological parameter optimization and quality effects on solid-liquid phase abrasive flow polishing

Electrochemical Analysis of the Slurry Composition for Chemical Mechanical Polishing of Flexible Stainless-Steel Substrates

Series Lectures on Metallic Chemical Polishing Technic PartⅠ-Chemical Polishing on Steel Parts

The Use of Pulsed Modes in the Electrochemical Polishing of Corrosion-Resistant Steels

Surface Finish Enhancement of Si(100) with Single Pole Magnetic Abrasive Finishing using Chemical Oxidizers and Alumina Slurry

Potassium persulfate as an effective oxidizer for chemical mechanical polishing of GCr15 bearing steel

Novel Eco-friendly Slurries for Chemical Mechanical Polishing of GCr15 Bearing Steel

The polishing mechanism of electrochemical mechanical polishing technology