Abstract:AISI 52100 steel has been widely used in the mechanical industry due to its excellent mechanical properties and high availability. In some cases, an ultra-smooth surface of AISI 52100 steel is needed and is even indispensable for the satisfactory performance of devices. In this paper, chemical mechanical polishing technique was employed to prepare the ultra-smooth surface of AISI 52100 steel. Colloidal silica was used as the abrasive. The effects of pH, complexing agent such as glycine, H2O2 and benzotriazole (BTA) on the polishing performance were studied. It is revealed that, with the increase of pH, the static etching rate (SER) and the material removal rate (MRR) are both gradually reduced, and the post-CMP surface roughness I?, decreases. This is attributed to the fact that compact and passive iron oxides, especially Fe(III) oxides, gradually form on the top surface. At pH 4.00, in the presence of glycine, and with the increase of the H2O2 concentration, the SER is further suppressed, and the surface roughness R-a gradually decreases; the MRR initially dramatically increases due to the fact that, with the addition of small amount of H2O2, the porous iron oxide layer with relatively low mechanical strength can be rapidly formed on the surface. Moreover, glycine intensifies the chemical dissolution by chelating iron ions, especially Fe(II) ions, and thereby the mechanical strength of the oxide layer further weakens. Then, after reaching the peak value, the MRR gradually decreases when the H2O2 concentration further increases since the compactness of the oxide layer gradually increases. With the increase of the BTA concentration, the MRR is gradually suppressed and the surface roughness R-a decreases due to the formation of Fe-BTA passivating film on the top surface. Finally, a two-step polishing process was developed. The polishing results show that, within 20 min, a rough surface of AISI 52100 steel with the R-a value of 188 nm can be polished into an ultra-smooth surface with the R-a value of 1.8 nm. (C) 2015 Elsevier B.V. All rights reserved.

Enhancing Chemical Mechanical Polishing Efficiency of Steel with Sulfate

Potassium persulfate as an effective oxidizer for chemical mechanical polishing of GCr15 bearing steel

Achieving a super-smooth surface of stainless bearing steel with chemical mechanical polishing via controlling corrosive wear of Fe and Cr

Novel Eco-friendly Slurries for Chemical Mechanical Polishing of GCr15 Bearing Steel

Chemical Mechanical Polishing of Steel Substrate Using Colloidal Silica-Based Slurries

Enhancing Tribological Properties of 18CrNiMo7-6 through Grain Refinement incorporating Al 2 O 3 particles

Chemical Mechanical Polishing of Mo Using H2O2 as Oxidizer in Colloidal Silica Based Slurries

Effects of Ph and Oxidizer on Chemical Mechanical Polishing of Aisi 1045 Steel

Exploiting the effect of PEO parameters on the surface of AISI 1020 low-carbon steel treated in a TaOH-rich electrolyte

Electrochemical Corrosion Behavior and Theoretical Simulation of Cobalt in Chemical Mechanical Polishing Process

Electrochemical Analysis of the Slurry Composition for Chemical Mechanical Polishing of Flexible Stainless-Steel Substrates

A special electrostatic self-assembly structure of colloidal silica: Improving Chemical Mechanical Polishing performance

Design and Study of a New QPQ Combined with Ultrasonic Roller Pressing Method for Gear Surface Strengthening

Synergism Between Wear and Corrosion of Cr26Mo1 Ferrite Stainless Steels in 0.5 mol/L of Sulfuric Acid

A novel process of chemical mechanical polishing for FV520B steel

Mechanism of material removal in tungsten carbide-cobalt alloy during chemistry enhanced shear thickening polishing

A Novel Approach of Chemical Mechanical Polishing for a Titanium Alloy Using an Environment-Friendly Slurry

Tribological Behaviors of Steel Surfaces Treated with Ion Sulphurization Duplex Processes

Tribological Behaviors of Self‒mated Cu36Zr48Ag8Al8 Bulk Metallic Glass under H2SO4 Conditions with Different Concentrations

The Synergistic Effects of Tricresyl Phosphate Oil Additive with Chemico‐thermal Treatment of Steel Surfaces

Synergetic Effect of Chemical Components in a Tungsten CMP Slurry and the Evolution of Tungsten Surface Species