Abstract:Fully dense ceramics with retarded grain growth can be attained effectively at relatively low temperatures using a high-pressure sintering method. However, there is a paucity of in-depth research on the densification mechanism, grain growth process, grain boundary characterization, and residual stress. Using a strong, reliable die made from a carbon-fiber-reinforced carbon (Cf/C) composite for spark plasma sintering, two kinds of commercially pure α-Al2O3 powders, with average particle sizes of 220 nm and 3 μm, were sintered at relatively low temperatures and under high pressures of up to 200 MPa. The sintering densification temperature and the starting threshold temperature of grain growth (Tsg) were determined by the applied pressure and the surface energy relative to grain size, as they were both observed to increase with grain size and to decrease with applied pressure. Densification with limited grain coarsening occurred under an applied pressure of 200 MPa at 1050 °C for the 220 nm Al2O3 powder and 1400 °C for the 3 μm Al2O3 powder. The grain boundary energy, residual stress, and dislocation density of the ceramics sintered under high pressure and low temperature were higher than those of the samples sintered without additional pressure. Plastic deformation occurring at the contact area of the adjacent particles was proved to be the dominant mechanism for sintering under high pressure, and a mathematical model based on the plasticity mechanics and close packing of equal spheres was established. Based on the mathematical model, the predicted relative density of an Al2O3 compact can reach ∼80 % via the plastic deformation mechanism, which fits well with experimental observations. The densification kinetics were investigated from the sintering parameters, i.e., the holding temperature, dwell time, and applied pressure. Diffusion, grain boundary sliding, and dislocation motion were assistant mechanisms in the final stage of sintering, as indicated by the stress exponent and the microstructural evolution. During the sintering of the 220 nm alumina at 1125 °C and 100 MPa, the deformation tends to increase defects and vacancies generation, both of which accelerate lattice diffusion and thus enhance grain growth.

Modeling the Densification of Boron Carbide Based Ceramic Materials under Flash Pressure Sintering

Numerical Simulation of Physical Fields during Spark Plasma Sintering of Boron Carbide

Modeling morphology evolution and densification during solid-state sintering via kinetic Monte Carlo simulation

Continuum Modeling of B4C Densification During Spark Plasma Sintering

Densification Behavior of Flash Sintered Boron Suboxide

Multi-stage spark plasma sintering to study the densification mechanisms of boron carbide

Densification and grain growth kinetics of boron carbide powder during ultrahigh temperature spark plasma sintering

Pressureless Sintering of Zirconium Diboride Ceramics with Boron Additive

Novel approach of the evaluation of electric current density during the spark plasma sintering: Effect on the densification mechanisms of B4C-based ceramics

Densification mechanism, microstructure and mechanical properties of ZrC ceramics prepared by high-pressure spark plasma sintering

Investigation of the effect of pressure, sintering temperature and time on silicon carbide microstructure

Models for the behavior of boron carbide in extreme dynamic environments

Progress in pressureless sintering of boron carbide ceramics – a review

Effect of the Addition of Carbon on the Sintering Properties of Boron Carbide Ceramics Prepared by Pressureless Sintering

Sintering pure polycrystalline boron carbide bulks with enhanced hardness and toughness under high pressure

Kinetic and thermophysical phenomena in the synthesis of porous composites from (Ti+Si) and (Ti+Al+Si) powder mixtures in the reaction sintering mode

The densification behavior of flash sintered BaTiO3

Pressureless sintering and properties of additively manufactured ZrB2–SiC

Sintering mechanism of pure B4C ceramic prepared by hot oscillating pressing and with excellent mechanical properties

Densification mechanism and microstructure characteristics of nano- and micro- crystalline alumina by high-pressure and low temperature sintering

Quantitative analysis and comparison on densification kinetics and grain growth mechanisms using reactively and directly densified TiB 2 -SiC- h BN ceramics